23 |
A x i o m T o o l G r o u p
Setting Spindle RPM:
The V5 Model machines are equipped with a LiteOn VFD invertor for spindle RPM control. This can be found on the
front of the white control box.
To adjust the RPM, simply turn the dial. Clockwise (right) to increase
RPM and Counter-clockwise (left) to decrease RPM.
This can be adjusted at any time. Included during a machine
operation. Allowing RPM to be dialed in dynamically as needed.
The display shows the RPM in shortened form. This means that while
the Spindle is OFF an RPM of 24,000, would be displayed simply as
24 when the dial is turned.
Once the Spindle is activated the display would read :2400 as shown above.
The buttons on the VFD, are intended to be used for programming only and should not be used to set the spindle
speeds.
Processing a File:
Selecting and Running a Toolpath
Once the
Origin
is placed (all axes) and the RPM is set, the file can be selected, and machining can begin.
To ease the use of a USB flash drive (U-disk), once files are saved to the U-disk always select to Eject the drive to
safely remove it from the computer. This will help ensure that the controller will recognize the U-disk when it is
inserted.
To begin (From the coordinate screen):
1-
Press the
Run/Pause/Delete
button.
2-
Select either the U-disk, Internal Memory a Recently used file (must be one current U-disk or in memory)
a.
Use the X+/- arrows to scroll up or down the list.
b.
Highlight the desired selection and press
OK
to select.
3-
The files in that directory will be displayed.
a.
Display shows three files at a time.
b.
X+/- will scroll one item at a time.
c.
Y+/- will scroll one page at a time.
d.
Highlight the desired tool-path (.mmg filetype), press
OK
to select
4-
The controller will display a set of working parameters for the file.
a.
Work Speed: Similar to feed-rate. This can be ignored as the controller is setup by default to take the
feed-rate settings from the software.
Settings can be changed allowing feed-rate to be set here
.
b.
Fast Speed: Shuttle speed. This is the speed the machine will travel between cutting locations.
c.
Speed Scale: A percentage of the feed-rate. (
See Speed Scale Adjustment
)
5-
Press
OK
to begin the tool-path operation.
a.
After a short count-down (4sec) during which the spindle will come up to speed, the file will begin.
During file operation, the lower line of the screen will rotate through a list of information. Including;
current g-code line (source number), operating time, speed (mm/min) and file name. Use the Mode
button to manually scroll this list.
Summary of Contents for AUTO ROUTE PRO V5
