background image

CARDIOID SET UP

The cardioid preset must be used in a sub array of three SW36XFA. Two box must be oriented towards the audience and one must be turned in 

the opposite direction (typically the box in the centre of the array). The bottom and the top boxes must have the STANDARD PRESET, the box in 

the middle must have the CARDIOID PRESET. The audio signal sent to all boxes is the same.

The CARDIOID PRESET has the same response of the STANDARD PRESET, but to obtain the maximum cancellation on the back side of the array it 

has the phase inverted and a proper level and delay setting.

The figure below shows two typical displacement of the array. The first with all the boxes in vertical position for a total height of 2400 mm and a 

width of 750 mm. The second one with all the boxes in vertical position for a total height of 800 mm and a width of 2240 mm.

use the AXFEETKIT (optional)

on all the SW36XFA which permit

to slot in the boxes

80 cm min.

2.7 ft min.

120 cm min.

3.9 ft min.

80 cm min.

2.7 ft min.

stage

wall or other

big ostacle

bass sum direction

bass cancellation direction

audience floor

NOTES:

When placing the cardioid array keep a distance to walls or other obstacles of at least 80 cm (2.6 ft) in order not to affect the radiation of the 

reversed cabinet.

When placing multiple cardioid arrays keep a distance between them of at least 120 cm (3.9 ft) in order not to maximize the combined radiation 

of whole arrays.

Summary of Contents for SW36XFA













Reviews: