AVTECH ELECTROSYSTEMS AVRK-3-B Instructions Manual Download Page 6 | Manualshive

Page: 6 / 43

background image

AVAILABLE OPTIONS

The AVRK-3-B is available with several options:

-OS Option: an externally generated DC offset (± 50 Volts, 250 mA DC maximum) can
be added to the output.

-EA Option: the amplitude can be controlled by an externally generated 0 to +10V
analog control voltage.

-R5 Option: This is the optional rack-mounting kit. The R5 rack-mount kit may also be
ordered separately.

6

«
...
4
5
6
7
8
...
»

Summary of Contents for AVRK-3-B












































Reviews:

No comments

Related manuals for AVRK-3-B

Brand: Champion Pages: 34

Brand: Agilent Technologies Pages: 126

Brand: Altrad Pages: 56

Brand: Powermate Pages: 72

PowerPact G0069981

Brand: Generac Power Systems Pages: 36

CENTURION 006104-1

Brand: Generac Power Systems Pages: 56

Brand: Micro-Pulse Pages: 15

Brand: Coleman Pages: 8

Powermate PM0463300.01

Brand: Coleman Pages: 12

Brand: Johnson Controls Pages: 8

Brand: Black & Decker Pages: 125

Brand: Yamaha Pages: 66

Brand: Yamaha Pages: 144

Brand: Gillette Generators Pages: 30

Brand: Electro Adda Pages: 31

Brand: AL-KO Pages: 182

Brand: Briggs & Stratton Pages: 8

Brand: Briggs & Stratton Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands