background image

and that this pulse generator meets the intent of the Low Voltage Directive 2006/95/EC.
Compliance pertains to the following specifications as listed in the official Journal of the 
European Communities:

EN 61010-1:2001

Safety requirements for electrical equipment for 
measurement, control, and laboratory use

DIRECTIVE 2011/65/EU (RoHS)

We

Avtech Electrosystems Ltd.
P.O. Box 5120, LCD Merivale
Ottawa, Ontario
Canada  K2C 3H5

declare that, to the best of our knowledge, all electrical and electronic equipment (EEE) 
sold by the company are in compliance with Directive 2011/65/EU of the European 
Parliament and of the Council of 8 June 2011 on the restriction of the use of certain 
hazardous substances in electrical and electronic equipment (also known as “RoHS 
Recast”). In addition, this declaration of conformity is issued under the sole 
responsibility of Avtech Electrosystems Ltd. Specifically, products manufactured do not 
contain the substances listed in the table below in concentrations greater than the listed
maximum value.

Material/Substance

Threshold level

Lead (Pb)

< 1000 ppm (0.1% by mass)

Mercury (Hg)

< 1000 ppm (0.1% by mass)

Hexavalent Chromium (Cr6+)

< 1000 ppm (0.1% by mass)

Polybrominated Biphenyls (PBB)

< 1000 ppm (0.1% by mass)

Polybrominated Diphenyl ethers (PBDE)

< 1000 ppm (0.1% by mass)

Cadmium (Cd)

< 100 ppm (0.01% by mass)

Bis(2-ethylhexyl) phthalate (DEHP)

< 1000 ppm (0.1% by mass)

Butyl benzyl phthalate (BBP)

< 1000 ppm (0.1% by mass)

Dibutyl phthalate (DBP)

< 1000 ppm (0.1% by mass)

Diisobutyl phthalate (DIBP)

< 1000 ppm (0.1% by mass)

DIRECTIVE 2002/96/EC (WEEE)

European customers who have purchased this equipment directly from Avtech will have
completed a “WEEE Responsibility Agreement” form, accepting responsibility for WEEE
compliance (as mandated in Directive 2002/96/EC of the European Union and local 

10

Summary of Contents for AVRK-3-B












































Reviews: