manualshive.com logo in svg

AVTECH ELECTROSYSTEMS AVG-4A-B, Instructions Manual

Share
Download
AVTECH ELECTROSYSTEMS AVG-4A-B Instructions Manual Download Page 3

TABLE OF CONTENTS

 

 

WARRANTY......................................................................................................................2
TECHNICAL SUPPORT...................................................................................................2
TABLE OF CONTENTS....................................................................................................3
INTRODUCTION...............................................................................................................5
SPECIFICATIONS............................................................................................................6
REGULATORY NOTES....................................................................................................7

FCC PART 18.......................................................................................................................... 7
EC DECLARATION OF CONFORMITY..................................................................................7
DIRECTIVE 2011/65/EU (RoHS).............................................................................................8
DIRECTIVE 2002/96/EC (WEEE)............................................................................................8
FIRMWARE LICENSING.........................................................................................................9

INSTALLATION..............................................................................................................10

VISUAL CHECK....................................................................................................................10
POWER RATINGS................................................................................................................10
CONNECTION TO THE POWER SUPPLY...........................................................................10
PROTECTION FROM ELECTRIC SHOCK...........................................................................11
ENVIRONMENTAL CONDITIONS........................................................................................12

FUSES.............................................................................................................................13

AC FUSE REPLACEMENT...................................................................................................13
DC FUSE REPLACEMENT...................................................................................................14
FUSE RATINGS....................................................................................................................14

FRONT PANEL CONTROLS..........................................................................................15
REAR PANEL CONTROLS............................................................................................17
GENERAL INFORMATION............................................................................................19

BASIC PULSE CONTROL....................................................................................................19
TRIGGER MODES................................................................................................................20
GATING MODES...................................................................................................................20
AMPLITUDE DRIFT..............................................................................................................21

AVAILABLE OPTIONS...................................................................................................22

-M OPTION............................................................................................................................ 22
-OS OPTION.......................................................................................................................... 22

PROTECTING YOUR INSTRUMENT.............................................................................23

TURN OFF INSTRUMENT WHEN NOT IN USE...................................................................23

3

Summary of Contents for AVG-4A-B







































Reviews:

No comments

Brands by name

Popular brands

Load more brands