AVS TITAN HD-SDI16 User Manual Download Page 17

Page: 17 / 84

Connecting other devices

Basic connections

Connecting a monitor

Check monitor resolution and connect to DVR.



HDMI Port : 1920 x 1080p

<Note>
We strongly recommend using HDMI certified cable when connecting to DVR.

Connecting a Camera

Connect 1080P, 720P, 960H, NTSC/PAL camera using recommended cable.

Recommended cable *

Depends on manufacturer and models.



Transmission distance will be affected by cable types and installation site environment



Transmission distance of the chosen cable will be various based on reduction rate of 750MHz
(reduction rate of dB/100m < 25dB is recommended)



Foamed or high-foamed trishield cable is recommended.



Impedance 75Ω must be used for coax cable connection and connector work.



Beware of deformation of cable due to high pressure over the cable.



Don’t pull the cable with too much force.



For DVR input/output, cables will be tied at the rear of the rack. If tied too tightly, inside/outside insulator can be
deformed so tie it loosely within cable’s curvature range.

Cable Type

HD-SDI transmission

distance *

Use

5C2V

about 90M

Analog signal

4C-FB(T), 4C-HFB(T), RG59

about 140M

High-foamed cable, double or triple
shielded cables are recommended

5C-FB(T), 5C-HFB, L-6CHD, RG6

about 180M

HD-SDI cable

5C-HFBT

about 200M

HD-SDI cable

Summary of Contents for TITAN HD-SDI16





















































































Search results

Summary of Contents for TITAN HD-SDI16

Reviews:

Related manuals for TITAN HD-SDI16

Brands by name

Popular brands

AVS TITAN HD-SDI16, User Manual

Search results

Summary of Contents for TITAN HD-SDI16

Reviews:

Related manuals for TITAN HD-SDI16

Brands by name

Popular brands