- 6 -
XSAT WS 4 EXPANSION
Installation Manual
General information
•
The
XSAT WS 4
radio transceiver combines a traditional wire system with a line of wireless radio products (sensors, sirens and remote
controls) that allow you to extend the protection of the system.
•
This board is inserted in a thermoplastic container that optimizes its the performance.
•
Depending on the installation needs, the
XSAT WS 4
can also be placed at a distance from the controller with which it is combined using
the RS485 serial link.
•
Manage up to 32 sensors
•
Manage up to 64 remote controls
•
Manage 1 wireless siren
•
2 terminal Input or Output
•
Multi-color LED indicator
General characteristics
Input lines
No 32 configurable with automatic detection of the individually programmable
alarm and anti-tamper status; each input can be programmed in one of the
possible modes of operation.
Terminal T1 and T2
n° 2:
Input / Output.
The terminals T1 and T2 can be programmed as either an input zone 7 and zone 8 of the satel-
lite with one resistor (alarm only) or double resostor (alarm and tamper), both as Open Collector
outputs 7 and 8 with reference to negative; or both programs simultaneously (line input is unba
-
lanced directly by activation of the corresponding OC)
Capacity in open field
~ 200 meters
Programming:
from keyboard with guided menu
Connections:
Four-wire
Dimensions: (L x H x P):
119 x 83 x 10 mm
Container: (L x H x P)
129,5 x 92 x 15,5 mm
Environmental Conditions:
+5 °C / +55 °C
Voltage:
13,8 V =
Current consumption:
At rest: 30 mA / Receiving: 45 mA / Transmission: 70 mA
Protection grade:
IPX0
Bande di frequenza usate
Occupied frequency bands
(ETSI EN 300 220-3-2 V1.1.1 (2017-02)
Wireless alarm equipment)
Massima
potenza irradiata
Maximum
radiated power
Numero di banda
Band number
According to EC Decision
2013/752/EU [i.2]
Numero di sottoclasse
della Classe 1
Class 1 sub-class number
Commision Decision 2000/299/EU [i.5]
A
868,600 MHz to 868,700 MHz
<10 mW e.r.p.
49
32
D
869,300 MHz to 869,400 MHz
<10 mW e.r.p.
53
72
E
869,650 MHz to 869,700 MHz
<10 mW e.r.p.
55
34
XSA
T WS 4 compatibility with AVS
Electronics controllers
You can program, display and continuously monitor all functions of the
XSAT WS 4
satellite and the sensors via radio. Through an RS 485 serial
connection, the system directly recognizes all zone and tamper alarms and all technical information linked to the radio equipment (sensor anti
-
masking, sensor survival, battery-low sensors and radio interference).
The satellite has to be installed at least 20 cm away from electrical appliances or metal containers that could disturb its operation.
The power supply must come from a very low voltage safety circuit and having the characteristics of a limited, fuse-protected power source.
INSTALLATION AND MAINTENANCE MUST BE PERFORMED BY QUALIFIED PERSONNEL
Satellite Card XSAT WS 4
ENTERING WIRES
Strip the cable for 3 - 4 mm and with soft pres
-
sure insert it into the corresponding.terminal.
CABLES DISCONNECTION
With a screwdriver, press lightly
at the point indicated in the figu
-
re, and pull out simultaneously
the cable from its housing.
ON
12
34
56
78
TAMPER
S1
1
1
2
3
-
T T2 T1
-
DB DA
+
ON
12
34
56
78
