AVProEdge AC-MX-88 User Manual Download Page 22 | Manualshive

Page: 22 / 51

background image

22

WebUI: System - IP Settings

Host Name -

Devices name on the network. This field is automatically filled with Model Name by default.

Model Name -

Displays the AVProEdge Model/Part number.

Serial Number -

Displays the Serial Number of the matrix.

MAC Address -

Displays the devices MAC Address.

IP assignment -

This drop-down has two options.

1. Manual

2. Automatic (DHCP)

Default out of the box will be set to Automatic (DHCP), the IP Address, Subnet Mask, Gateway, Primary

DNS, and Secondary DNS will be assigned by your network controller. If you select Manual, you can use the

text fields to enter your own Network settings. Once all fields have been filled out, click the green Apply

Button to set. A prompt will appear to confirm the change, click OK to confirm.

This area contains relevant network information of the AC-MX-88.

«
...
20
21
22
23
24
...
»

Summary of Contents for AC-MX-88




















































Reviews:

No comments

Related manuals for AC-MX-88

Brand: Sams Pages: 10

Brand: SIMON RWA Pages: 3

Brand: Dahua Pages: 17

MatrixPRO 8x8 DVI

Brand: Barco Pages: 2

GlobeCaster STUDIO 4000

Brand: Global Streams Pages: 144

TNM4000-TP36FF4X16G24P

Brand: MRD Pages: 38

Brand: SICK Pages: 299

Brand: Labgear Pages: 8

Brand: AV-Box Pages: 11

Brand: CYP Pages: 20

Summit X450-G2-24t-GE4

Brand: Extreme Networks Pages: 2

Brand: ATEN Pages: 68

Brand: SEKURYX Pages: 13

Brand: TP-Link Pages: 2

Brand: WaveSplitter Pages: 35

Luzense RADIM RF

Brand: Unilamp Pages: 2

Brand: CYP Pages: 64

EMC PowerSwitch S5148F-ON

Brand: Dell Pages: 45

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands