manualshive.com logo in svg

Avnet SMARC MSC SM2S-IMX8M, User Manual, Page: 30 / 92

Share
Download
Avnet SMARC MSC SM2S-IMX8M User Manual Download Page 30

 

MSC SM2S-IMX8M User Manual 

 

 

 

 

 

 

 

30 / 92  

Signal 

Pin Type 

Signal 
Level 

Pin on 
i.MX8 

Pin name on i.MX8M 

Power 
Tolerance 

PU/PD 

Description 

PCIE_WAKE#  

I 

3.3V 
CMOS 

A3 

SAI1_MCLK 

 

3.3V 

PU 10k 

PCI Express Wake signal. Asserted by 
device when requesting wake up.  

(CPU GPIO4_IO20)

 

 

NOTE:  

PCIE_A_RST# and PCIE_B_RST# share same CPU pin. 

4.4  USB 

The USB controller supports USB 3.0 and USB 2.0. 

Depending on the module variant different number of USB lanes are available: 

 

Option 1

 with USB 3.0 Hub:   

 

  USB[0] = USB 2.0 host/device OTG compliant 

  USB[1] = USB 2.0 host   

  USB[2:3] = USB 3.0 host 

  USB[4] = USB 2.0 host. 

 

Option 2

 without USB 3.0 Hub:  

 

  USB[0] = USB 2.0 host/device OTG compliant  

  USB[1] = USB 2.0 host. 

 

Table 4-4: USB Signal Description 

Signal 

Option 
Availability 

Pin Type 

Signal Level 

Pin on 
i.MX8M 

Pin name on 
i.MX8M 

Power 
Toleranc
e 

PU/PD 

Description 

USB0+ 
USB0- 

1 & 2 

I/O 

USB 

A14 

B14 

USB1_DP 

USB1_DN 

3.3V 

 

Differential USB 2.0 data pairs 
connected to SoC. Can be 
configured as host or device. 

Summary of Contents for SMARC MSC SM2S-IMX8M





























































































Reviews:

No comments