manualshive.com logo in svg

AvL Technologies AAQ TLE Tracking Module, Set Up And Operation Manual

Share
Download
AvL Technologies AAQ TLE Tracking Module Set Up And Operation Manual Download Page 8

 

TLE Tracking Module Operations 

Guide

 

 

 

 

AvL Technologies

 | Proprietary – Content is Subject to Change without Notice                 

 

 

 7 

 

Manual Time Offset Date 

4 

String 

- 

The Date for Manual Time Offset. Format is MM-
DD-YYY in UTC 

Manual Time Offset Time 

4 

String 

- 

Time for Manual Time Offset. Format is 
hh:mm:ss in UTC 

 

 

TLE Reflector Size

 – The size of the reflector currently mounted on the antenna system, defined in meters. This is used 

to calculate the antenna’s half power beam width for scanning and tracking. 

AvL Compass Com Port

 – This should be set to “192.168.0.63” if the NAV RIOM GPS is being used as a Time Source or 

left blank otherwise. If this configuration item is changed, the antenna must be power cycled before the change will 
take effect. 

AvL Compass Com Port Settings

 – This should be set to “9760” if the NAV RIOM GPS is being used as a Time Source or 

left blank otherwise. If this configuration item is changed, the antenna must be power cycled before the change will 
take effect. 

Primary Heading Source

 – The heading source desired for acquisition. An accurate heading is desired. Set to Vector 

Compass, Manual, or Compass. 

Heading for Manual Compass

 – The heading to be used when the Heading Source is set to Manual 

Time Source

 – The current time source used to provide time sync to the AAQ controller. Accurate time is needed for 

TLE tracking. Set to Vector Compass GPS, Manual, or NAV RIOM GPS.   

GPS Source

 – The GPS source desired for acquisition. Set to Vector Compass GPS, Manual, or NAV RIOM GPS. 

 

The settings below can be used to provide manual overrides in the case of NAV RIOM or Vector Compass failure. 

Manual Latitude

 - The latitude in decimal degrees and direction to use when the GPS Source is Manual 

Manual Longitude

 - The longitude in decimal degrees and direction to use when the GPS Source is Manual 

Manual Time Offset Date

 – The date for Manual Time Source. Format is MM-DD-YYY in UTC. This format must be 

adhered to exactly (including the “-“) for correct operation. TLE Tracking requires an accurate date.

 This offset must be 

entered every time the antenna has been powered off for more than a minute and.

 

the antenna must be power cycled 

every time this is changed. 

Manual Time Offset Time

 – The time for Manual Time Source. Format is hh:mm:ss in UTC.  This format must be 

adhered to exactly (including the “:“) for correct operation. This offset must be entered every time the antenna is 
powered on. 

This offset must be entered every time the antenna has been powered off for more than a minute and.

 

the antenna must be power cycled every time this is changed. 

 

Summary of Contents for AAQ TLE Tracking Module






























Reviews:

No comments

Brands by name

Popular brands

Load more brands