Avital AVISTART 4501 Installation Manual Download Page 27

Page: 27 / 28

Programming Table for Remote Controls

Feature

Factory

Setting

No. of

Beeps

Secondary Action

Remote Door Lock/Panic

Button

Press the

Button, the piezo

beeper will beep 1 time

Remote Door Unlock

Button

Press the

Button, the piezo

beeper will beep 2 times

Remote Engine Start

Button

Press the

Button, the piezo

beeper will beep 3 times

Remote Trunk Release

Button

Press the

Button, the piezo

beeper will beep 4 times

Temperature Controlled Start

Active/Inactive

Button

Press the

Button, the piezo

beeper will beep 5 times

Remote Accessory Output (-)

Button

Press the

Button, the

piezo beeper will beep 6 times

All Learn

Button

Press the

Button, the piezo

beeper will beep 1 time

Delete All

Wait 3 seconds, the piezo beeper

will beep twice, all codes are

erased out of memory.

AviStart 4501 Installation Manual - 0999

Summary of Contents for AVISTART 4501





























Search results

Summary of Contents for AVISTART 4501

Reviews:

Related manuals for AVISTART 4501

Brands by name

Popular brands

Avital AVISTART 4501, Installation Manual

Search results

Summary of Contents for AVISTART 4501

Reviews:

Related manuals for AVISTART 4501

Brands by name

Popular brands