Avital AviStart 3000 Page 5 Installation Manual Download

Page: 5 / 40

installation points to remember

IMPORTANT!

This product is designed for fuel-injected, automatic transmission vehicles only.

Installing it in a standard transmission vehicle is dangerous and is contrary to its intended use.

Before beginning the installation:

■

Please read this entire installation guide before beginning the installation. The installation of this remote

start system requires interfacing with many of the vehicle’s systems. Many new vehicles use low-voltage or

multiplexed systems that can be damaged by low resistance testing devices, such as test lights and logic

probes (computer safe test lights). Test all circuits with a high quality digital multi-meter before making con-

nections.

■

Do not disconnect the battery if the vehicle has an anti-theft-coded radio. If equipped with an air bag, avoid

disconnecting the battery if possible. Many airbag systems will display a diagnostic code through their

warning lights after they lose power. Disconnecting the battery requires this code to be erased, which can

require a trip to the dealer.

■

Remove the domelight fuse. This prevents accidentally draining the battery.

■

Roll down a window to avoid being locked out of the vehicle.

After the installation:

■

Test all functions. The "Using Your System" section of the Owner's Guide is very helpful when testing.

■

Complete the vehicle

Safety Check

outlined in this manual prior to the vehicle reassembly.

Summary of Contents for AviStart 3000









































Search results

Summary of Contents for AviStart 3000

Reviews:

Related manuals for AviStart 3000

Brands by name

Popular brands

Avital AviStart 3000, Installation Manual

Search results

Summary of Contents for AviStart 3000

Reviews:

Related manuals for AviStart 3000

Brands by name

Popular brands