Avital AviStart 3000 Page 3 Installation Manual Download | Manualshive

Page: 3 / 40

background image

table of contents

© 2001 Directed Electronics, Inc. Vista, CA

3

What Is Included

. . . . . . . . . . . . . . . . . . . . . 3

Warning! Safety First

. . . . . . . . . . . . . . . . . . 4

Installation Points to Remember

. . . . . . . . . . 5

Finding The Wires You Need

. . . . . . . . . . . . . . 6

Obtaining Constant 12V . . . . . . . . . . . . . . . 6
Finding the Starter Wire. . . . . . . . . . . . . . . 6
Finding the 12V Switched Ignition Wire . . . . 7
Finding the Accessory Wire . . . . . . . . . . . . . 7
Finding a (+) Parking Light Wire . . . . . . . . . 7
Finding the Tachometer Wire. . . . . . . . . . . . 8
Finding the Wait-To-Start Bulb
Wire For Diesels . . . . . . . . . . . . . . . . . . . 9

Primary Harness (H1) Wiring Diagram

. . . . . . . 9

Remote Start Ribbon Harness Wiring Diagram

. 10

Heavy Gauge Relay Satellite Wiring Diagram

. . 10

Remote Start Harness (H2) Wiring Diagram

. . 10

Primary Harness (H1) Wire Connection Guide

. 11

Relay Satellite Key Switch Interface Wire
Connection Guide

. . . . . . . . . . . . . . . . . . . . 14

Remote Start Harness (H2) Wire
Connection Guide

. . . . . . . . . . . . . . . . . . . . 15

Neutral Safety Switch Interface

. . . . . . . . . . 16

GM Trucks, SUVs and Column-Shifting
Passenger Cars . . . . . . . . . . . . . . . . . . . . 18
Pre-1996 Dodge Dakota Pickups with
2.5 Liter Motors . . . . . . . . . . . . . . . . . . . 18

Bypassing GM Vehicle Anti-Theft Systems (VATS)

. 19

1995 and Newer Vehicle Anti-Theft
Systems (Immobilizers)

. . . . . . . . . . . . . . . . 20

Passlock I and Passlock II (PL-1 and PL-2). . 20
Passkey III (PK-3), Transponder-Based Systems . 20

Optional Anti-Grind Relay

. . . . . . . . . . . . . . 21

Door Lock Wiring Guide

. . . . . . . . . . . . . . . . 22

Positive-Triggered, Relay Driven
Systems (Type A) . . . . . . . . . . . . . . . . . . 22
Negative-Triggered, Relay Driven
Systems (Type B) . . . . . . . . . . . . . . . . . . 23
Reversing Polarity System (Type C) . . . . . . . 24
After-Market Actuators (Type D) . . . . . . . . . 25
Electrically Activated Vacuum (Type E) . . . . 26
One-Wire System, (Type F) . . . . . . . . . . . . 26
Positive (+) Multiplex, (Type G) . . . . . . . . . 27
Negative (-) Multiplex, (Type H) . . . . . . . . 28

Internal Programming Jumper

. . . . . . . . . . . 29

Digital Tach Threshold On/Off . . . . . . . . . . 29

Plug-in Program Switch

. . . . . . . . . . . . . . . . 30

Transmitter/Receiver Learn Routine

. . . . . . . . 30

Tach Learning

. . . . . . . . . . . . . . . . . . . . . . . 31

Operating-Settings Learn Routine

. . . . . . . . . 32

Features Menu

. . . . . . . . . . . . . . . . . . . . . . 33

Feature Descriptions

. . . . . . . . . . . . . . . . . . 33

Shutdown Diagnostics

. . . . . . . . . . . . . . . . . 35

Timer Mode

. . . . . . . . . . . . . . . . . . . . . . . . 36

Safety Check

. . . . . . . . . . . . . . . . . . . . . . . 37

Troubleshooting

. . . . . . . . . . . . . . . . . . . . . 38

Wiring Quick Reference Guide

. . . . . . . . . . . 40

what is included

■

One control module

■

One 2-button remote transmitter (P/N 820021)

■

One plug-in Valet/program switch

■

One hood pinswitch

■

One toggle override switch

■

One 542G range-extender antenna

■

One 8-pin primary harness

■

One 6-pin remote start harness

■

One 5-pin harness with relay satellite

■

One remote start warning label

■

Two window decals

■

One patent card

■

One warranty reply card

■

One installation guide

■

One owner’s guide

«
1
2
3
4
5
...
»

Summary of Contents for AviStart 3000









































Reviews:

No comments

Related manuals for AviStart 3000

Brand: U-Prox Pages: 29

Brand: Ansel Pages: 84

Brand: Halma Pages: 8

SpreadNet SN962-PENDANT

Brand: C&K systems Pages: 2

IOLAN SDG1 LA/LE

Brand: Perle Pages: 21

Brand: Icare Pages: 27

Brand: COHU Pages: 21

Brand: Lawmate Pages: 1

XBC28V12DN1M3IR

Brand: XENO Pages: 2

Brand: Federal Signal Corporation Pages: 12

Brand: NorthQ Pages: 11

Brand: Bosean Electronic Technology Pages: 16

Brand: Chuango Pages: 18

ThermalTronix TT-H-BFTC Series

Brand: Intellisystem Pages: 7

Brand: Vista Pages: 22

Brand: Caliber Pages: 28

EN1260EchoStream

Brand: Inovonics Pages: 2

Mobile SMS Guard 300

Brand: Marmitek Pages: 52

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands