Avital AviStart 3000 Page 9 Installation Manual Download

Page: 9 / 40

In diesel vehicles it is necessary to interface with the wire that turns on the WAIT-TO-START light in the dash-

board. This wire illuminates the bulb until the vehicle’s glow plugs are properly heated. When the light goes out

the vehicle can be started. This wire is always available at the connector leading to the bulb in the dashboard.

It can also be found at the Engine Control Module (ECM) in many vehicles.

To test and determine the polarity of this wire:

1. Set your multimeter to DCV or DC voltage (12 or 20V is fine).

2. Attach the (+) probe of the meter to (+)12V.

3. Probe the wire that you suspect leads to the bulb with the (-) probe of the meter.

4. Turn the ignition switch to the ON position.

5. If the meter indicates 12 volts until the light goes out you have isolated the correct wire and the wire's polar-

ity is negative (ground while the bulb is on).

6. If the meter reads zero volts until the light goes out and then reads 12 volts, you have isolated the correct

wire and the wire's polarity is positive.

primary harness (H1) wiring diagram

______

LIGHT BLUE

(-) 200 mA DOOR UNLOCK OUTPUT

LIGHT GREEN

(-) 200 mA DOOR LOCK OUTPUT

GRAY/BLACK

(-) WAIT-TO-START INPUT

WHITE

(-) 200 mA LIGHT FLASH OUTPUT

YELLOW

(+) IGNITION (OUTPUT TO OPTIONAL SECURITY SYSTEM)

LIGHT GREEN/BLACK

(-) FACTORY DISARM/SPECIAL ACCESSORY

WHITE/BLUE

(-) REMOTE START ACTIVATION INPUT

BLACK

(-) CHASSIS GROUND INPUT

H1/1

H1/2

H1/3

H1/4

H1/5

H1/6

H1/7

H1/8

finding the wait-to-start bulb wire for diesels

Summary of Contents for AviStart 3000









































Search results

Summary of Contents for AviStart 3000

Reviews:

Related manuals for AviStart 3000

Brands by name

Popular brands

Avital AviStart 3000, Installation Manual

Search results

Summary of Contents for AviStart 3000

Reviews:

Related manuals for AviStart 3000

Brands by name

Popular brands