Avital AviStar 3300 Page 47 Installation Manual Download

Page: 47 / 50

long term event history

The system stores the last two full triggers in memory. These are not erasable. Each time the unit sees a full

trigger, the older of the two triggers in memory will be replaced by the new trigger. To access long term event

history:

With the ignition off, press and

HOLD

the Valet®/Program switch.

Turn on the ignition.

Release the Valet®/Program switch.

Press and release the Valet®/Program switch within 5 seconds. The LED will flash in groups

indicating the last two zones that triggered the unit for one minute or until the ignition

is turned off.

NOTE:

The Warn Away triggers are not stored to memory and will not be reported.

safety check

Before vehicle reassembly, the remote system must be checked to ensure safe and trouble-free operation. The fol-

lowing test procedure must be used to verify proper installation and operation of the system. The installation

must be completed before testing, including connection to the brake switch and hood switch.

1. Test the BRAKE shutdown circuit: With the vehicle in Park (P), activate the remote start system. Once the

engine is running, press the brake pedal. The engine should shut down immediately. If the engine continues

to run, check the brake circuit connection.

2. Test the HOOD PIN shutdown circuit: With the vehicle in Park (P), open the hood. Activate the remote start

system. The vehicle should not start. If the starter engages, check your hood pin and connections.

NOTE:

If programmed for Diesel Mode, the system will turn on the ignition, but the starter should

not engage with the hood open.

Summary of Contents for AviStar 3300



















































Search results

Summary of Contents for AviStar 3300

Reviews:

Related manuals for AviStar 3300

Brands by name

Popular brands

Avital AviStar 3300, Installation Manual

Search results

Summary of Contents for AviStar 3300

Reviews:

Related manuals for AviStar 3300

Brands by name

Popular brands