Avital AviStar 3300 Page 11 Installation Manual Download

Page: 11 / 50

Most vehicles use negative door trigger circuits. Connect the green wire to a wire which shows ground when any

door is opened. In vehicles with factory delays on the domelight circuit, there is usually a wire that is unaffected

by the delay circuitry. This wire will report Zone 3.

Inputs shorter than 0.8 seconds will trigger the Warn Away response, while inputs longer than 0.8 seconds will

trigger the full alarm sequence. If installing an optional DEI® dual stage sensor, connect both the blue and the

green wires of the optional sensor to this input. This wire will report Zone 4.

This wire is used in vehicles that have a positive (+) switched dome light circuit. Connect the violet wire to a

wire that shows (+)12V when any door is opened, and ground when the door is closed. This wire will report Zone 3.

Remove any paint and connect this wire to bare metal, preferably with a factory bolt rather than your own screw.

(Screws tend to either strip or loosen with time.) We recommend grounding all your components, including the

siren, to the same point in the vehicle.

H1/8 BLACK (-) chassis ground connection

H1/7 VIOLET (+) door trigger input, zone 3

H1/6 BLUE (-) multiplex input, zone 4

H1/5 GREEN (-) door trigger input, zone 3

Summary of Contents for AviStar 3300



















































Search results

Summary of Contents for AviStar 3300

Reviews:

Related manuals for AviStar 3300

Brands by name

Popular brands

Avital AviStar 3300, Installation Manual

Search results

Summary of Contents for AviStar 3300

Reviews:

Related manuals for AviStar 3300

Brands by name

Popular brands