Avital 2100 Installation Manual Download | Manualshive

Page: 18 / 26

background image

18

© 2001 Directed Electronics, Inc. Vista, CA

internal programming jumper

This jumper is used to determine the light flash output. In the (+) position, the on-board relay is enabled and

the unit will output (+)12V on the H1/2 WHITE wire. In the (-) position, the on-board relay is disabled. The H1/2

WHITE wire will supply a (-) 200 mA output suitable for driving factory parking light relays. To access the jumper,

open the control module.

NOTE:

For parking light circuits that draw 10 amps or more, the internal jumper must be switched

to a (-) light flash output.

P/N 8617

or a standard automotive SPDT relay must be used on the

H1/2 light flash output harness wire.

light flash jumper

«
...
16
17
18
19
20
...
»

Summary of Contents for 2100



























Reviews:

No comments

Related manuals for 2100

Brand: Bang & Olufsen Pages: 20

Brand: Directed Electronics Pages: 37

Brand: Basic XL Pages: 56

Brand: Olympia Pages: 4

BW-2500 PREMIER PLUS

Brand: Black Widow Pages: 8

Brand: Emerald Pages: 4

Brand: Iluv Pages: 1

Brand: Audiovox Pages: 10

Brand: System Sensor Pages: 4

Brand: Philips Pages: 2

Brand: Audiovox Pages: 8

Brand: Technoline Pages: 48

Brand: DSC Pages: 4

Brand: EST International Pages: 4

Brand: EST Pages: 4

Brand: IKEA Pages: 36

Brand: Eurochron Pages: 8

Brand: E-Pill Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands