Avital 2100 Installation Manual Download Page 7 | Manualshive

Page: 7 / 26

background image

© 2001 Directed Electronics, Inc. Vista, CA

7

Remove any paint and connect this wire to bare metal, preferably with a factory bolt rather than your own screw.

(Screws tend to either strip or loosen with time.) We recommend grounding all your components, including the

siren, to the same point in the vehicle. See the following diagram.

Connect this wire to an ignition source. This input must show (+)12V with the key in run position and during

cranking. Make sure that this wire cannot be shorted to the chassis at any point. This wire will report Zone 5.

Connect this to the red wire of the siren. Connect the black wire of the siren to (-) chassis ground, preferably at

the same point you connect the control module’s black ground wire.

H1/10 BROWN (+) siren output

H1/9 YELLOW (+) ignition input, zone 5

H1/8 BLACK (-) chassis ground connection

«
...
5
6
7
8
9
...
»

Summary of Contents for 2100



























Reviews:

No comments

Related manuals for 2100

Predator EVO4+2

Brand: Falcon Pages: 11

Brand: AVS Pages: 4

Brand: LST Pages: 1

Brand: Jensen Pages: 22

Brand: Magicar Pages: 61

Brand: Smoke hollow Pages: 22

EZ Wake SunRise

Brand: BioBrite Pages: 2

nightvision 21103

Brand: Equity Pages: 2

Brand: Equity Pages: 2

Brand: Equity Pages: 2

Brand: Equity Pages: 2

Brand: Equity Pages: 3

Brand: Equity Pages: 2

Brand: Jazwares Pages: 18

Brand: KRHÜNER Pages: 12

Brand: Skybrake Pages: 2

Brand: family first Pages: 2

Brand: family first Pages: 2

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands