Avital 2000 Operation Manual Download | Manualshive

Page: 16 / 24

background image

16

© 2001 Directed Electronics, Inc. Vista, CA

1. Cut the output wire from the door lock switch/key cylinder in half.

2. Test with the meter from the switch side of the cut door lock switch/key cylinder wire to a reliable ground

source. Some good ground references are the ground input source to the door lock switch/key cylinder or the

battery ground.

3. Operate the door lock switch/key cylinder in both directions to determine the resistor values. If the multi-

meter displays zero resistance in one direction, no resistor is needed for that direction.

4. Once the resistor value(s) is determined, refer to the wiring diagram for proper wiring.

«
...
14
15
16
17
18
...
»

Summary of Contents for 2000

























Reviews:

No comments

Related manuals for 2000

Brand: LEXIBOOK Pages: 9

Brand: La Crosse Technology Pages: 10

Brand: BALDR Pages: 24

Brand: Tanda Pages: 9

Brand: Bellman Pages: 4

Brand: ZAZU Pages: 23

Brand: Cobra Pages: 28

EVO ONE THAR-ONE-KHY2

Brand: Fortin Pages: 8

Brand: Lenoxx Pages: 7

Brand: Prestige Pages: 16

Brand: Hanhart Pages: 18

Brand: Sunrise System Pages: 15

Brand: Equity Pages: 2

Brand: Equity Pages: 2

Brand: Equity Pages: 2

Brand: Equity Pages: 2

Brand: Fire-Lite Alarms Pages: 2

Brand: Orca Pages: 24

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands