Installation Manual
Radar Sensor Setup
P/N 600-00175-000 Rev 04
- 54 -
◆
When you reach the desired setting, quickly adjust the TILT SETTING to above 10 UP to
lock in the setting.
4.
Proceed to step L.
Note:
If the 400 Hz REF field is zero (0), and does not change when the TILT knob is adjusted,
check that the correct gyro has been selected when programming the Configuration Module.
L.
Calibrate PITCH GAIN
1.
Set the tilt table for 10
o
pitch up.
2.
Use the GAIN control to set the GAIN POT /2 setting to 25- or 26-.
3.
Set the PITCH ANGLE field to 10.0 ±1.0
o
.
◆
To increment the value of the PITCH ANGLE, use the right inner knob to change the TILT
SETTING to between 5 and 10 UP. When the TILT SETTING is set to between 5 and 10
UP, the value of the PITCH ANGLE field will slowly increase.
◆
To decrement the value of PITCH ANGLE, use the right inner knob to change the TILT
SETTING to between 5 and 10 DOWN. When the TILT SETTING is set to between 5 and
10 DOWN, the value of the PITCH ANGLE field will slowly decrease.
◆
When you reach the desired setting, quickly adjust the TILT SETTING to above 10 UP to
lock in the setting.
4.
Set for 10
o
PITCH DOWN. Repeat steps 2 and 3.
5.
Set the tilt table to 0
o
pitch and roll.
6.
Proceed to step M.
M.
Calibrate PITCH OFFSET
1.
Use the GAIN controls to set the GAIN POT /2 setting to 18- or 19-.
2.
Check that the tilt table is set for 0
o
pitch.
3.
Set the PITCH ANGLE field to 0.0 ±1.0
o
.
◆
To increment the value of the PITCH ANGLE, use the right inner knob to change the TILT
SETTING to between 5 and 10 UP. When the TILT SETTING is set to between 5 and 10
UP, the value of the PITCH ANGLE field will slowly increase.
◆
To decrement the value of PITCH ANGLE, use the right inner knob to change the TILT
SETTING to between 5 and 10 DOWN. When the TILT SETTING is set to between 5 and
10 DOWN, the value of the PITCH ANGLE field will slowly decrease.
◆
When you reach the desired setting, quickly adjust the TILT SETTING to above 10 UP to
lock in the setting.
4.
Set the tilt table to 10
o
pitch up. The value should be 10.0U ±1.0
o
. If the value is out of range,
repeat step L.
5.
Set the tilt table to 10
o
pitch down. The value should be 10.0D ±1.0
o
. If the value is out of
range, repeat step L.
6.
Set the tilt table to 0
o
pitch. The value should be 0.0 ±1.0
o
. If the value is out of range, repeat
this step (step M.).
Summary of Contents for FlightMax EX500
