manualshive.com logo in svg

Avidyne FlightMax EX500, Installation Manual

Share
Download
Avidyne FlightMax EX500 Installation Manual Download Page 49

 

Installation  Manual

 

P/N 600-00175-000 Rev 04

MFD Feature Setup and Checkout

- 39 -

5.6.3  Lightning Sensor Noise Mode

When operating the Lightning sensor (WX-500 only) in Noise Monitor mode, the Lightning button on 
the Map page will display “Noise” as the current Lightning state. 

➥

Do not press the button in this state, or it may suppress lightning display unnecessarily. 

See the operating guide for the Lightning Sensor for more information.

If no lightning strikes are shown at all during noise testing, press the button until it says Display Off, 
then press once more to return to the proper Noise mode display.

Lightning Sensor is Not Communicating

Communication between the Lightning sensor to the MFD has been 
lost. 

■

Ensure that the wiring between the MFD and the Lightning 

sensor is correct.

■

Check the port configuration for the Lightning sensor.

■

The Lightning sensor may have an error.

Lightning Ahead

The Lightning Ahead option has been checked on the Lightning 
Setup page. Displays when a Lightning Ahead condition exists.

Lightning Heading Source Failed

Heading data is no longer available from the WX-500. Strike data 
may still be valid. Will only appear if the WX-500 is used as the 
heading source.

Lightning Heading Source OK

Heading data has been restored.

Stuck mic-PLEASE CHECK

Check your COM transmitters for indication of a stuck mike.

Lightning Antenna Location Changed

There may be an inconsistency between the antenna location 
jumper setting and the software configuration. This message should 
only appear during installation.

Lightning Position Source Failed 

(TWX670 

only)

The position reporting source (GPS or FMS) connected to the 
TWX670 has encountered a fatal fault.

Lightning Position Source OK 

(TWX670 only)

The position reporting source (GPS or FMS) connected to the 
TWX670 has returned to normal operation.

Noise Present 

(TWX670 only)

The TWX670 has detected excessive noise in the system. 
Accuracy and efficiency of the lightning sensor may be 
negatively affected.

Stuck MK 

(TWX670 only)

Microphone PTT switch is stuck open. Lightning strikes will 
not be displayed until the problem is fixed.

No Position Data 

(TWX670 only)

The position reporting source (GPS or FMS) connected to the 
TWX670 is not sending position data.

Table 16:  Lightning Sensor Messages (Continued)

Message

Meaning

Summary of Contents for FlightMax EX500





























































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands