manualshive.com logo in svg

Avery Weigh-Tronix ZP900, User Instructions

Share
Download
Avery Weigh-Tronix ZP900 User Instructions Download Page 37

 38

ZP900 Post Scales User Instructions

Outline dimensions and connections

8.1.2  Connecting a 2nd Remote Display

To connect a 2nd Remote Display requires connecting from Com2 of the ZP900 to 
Com1 of the 2nd Remote Display.

For the 2nd Remote Display to function the ZP900 will need to be configured for Serial 
port 2 (9600, 8, n, 1) and Protocol 2 (SMA to Port 2). 

2 wires will need to be attached to TB3 pin 1 (GND) and pin 6 (+5V) on the ZP900 
indicator.

In order to connect to a PC terminal using a serial RS232 interface when two remote 
displays are already connected to the ZP900 serial ports, you can use Com 2 on either 
remote display and refer to the dip switch settings to select from an available protocol.

Wiring instructions - 2nd Remote Display to Indicator

Remote Display Serial Port

Indicator Serial Port

TB3 Pin 1 - Blue (GND)

TB3 Pin 1 - Blue (GND)

TB3 Pin 2 - White/Orange (TX1)

TB3 Pin 5 - White/Orange (RX2)

TB3 Pin 4 - White/Blue (RX1)

TB3 Pin 3 - White/Blue (TX2)

TB3 Pin 6 - Orange (+5V) 

TB3 Pin 6 - Orange (+5V)

Summary of Contents for ZP900










































Reviews:

No comments

Brands by name

Popular brands

Load more brands