manualshive.com logo in svg

Avery Berkel A301CE, Service Instructions Manual, Page: 31 / 168

Share
Download
Avery Berkel A301CE Service Instructions Manual Download Page 31

3 —  Operation

Service  Instructions RP-A301CE/RP-A351CE/RP-A355CE

3 - 17

3.1.6

Cleaning A351CE

The machine must be cleaned once a day or
more frequently if necessary.

Clean all the parts using a cloth sprinkled
with water and washing up liquid (do not use
strong detergents) and a brush.

WARNING:

DO NOT USE A WATER JET.

DANGER:

PERFORM THE CLEANING
OPERATIONS WITH GREAT CARE:
DANGER OF INJURY.

Component removal

Product holder

1.

Loosen the product holder by rotating
the product holder clamping handle in
a counterclockwise direction.

2.

Position to zero the slice thickness
control to remove the product holder.

3.

Push the product holder towards the
operator until it clicks.  The click will
inform the operator that the product
holder is clamped.

4.

Lift the last slice device from the guide
bar.

Summary of Contents for A301CE









































































































































































Reviews:

No comments