avertX HD848IRM User Manual Download Page 15 | Manualshive

Page: 15 / 56

background image

37736AA

15

INSTALLING THE CAMERA

Wall and Ceiling Installation

1. Apply template sticker to desired camera location.
2. Drill anchor holes and 7/8” hole for cabling using included mounting template.

Note:

The 7/8” cabling hole is not required if a mounting accessory is being used.

3.  Remove mounting template.
4.  Insert anchors.
5.  Connect network cable with included waterproof cable connector.
6.  Remove the camera dome cover by removing 3 dome screws and lifting.
7.  Attach the camera to the ceiling or wall with the included screws.
8.  Adjust the camera to the desired angle.

•

The HD848IRM features 3-axis camera positioning: Tilt, Camera Rotation, and Lens

Rotation.

•

Rotate the lens so the 0 mark is vertical relative to the horizon.

Note:

Use the AvertX Connect app to view the camera while adjusting view.

9. Replace the dome cover. To install, align screws to the holes. Tighten dome cover screws

just enough for a good seal. Clean the dome with the included cleaning cloth.

10. Mount camera.
11. Install the camera cover and tighten the lock screw.

«
...
13
14
15
16
17
...
»

Summary of Contents for HD848IRM

























































Reviews:

No comments

Related manuals for HD848IRM

Brand: Samsung Pages: 149

Brand: Dante Pages: 10

Brand: Olympus Pages: 268

Brand: Zavio Pages: 13

Brand: Super Circuits Pages: 28

Brand: SOMFY Pages: 40

Brand: Freefly Pages: 8

Brand: Velleman Pages: 20

Brand: Nauticam Pages: 19

Brand: Ikegami Pages: 36

LFP Battery S Series

Brand: RAYSTECH Pages: 10

Brand: General Lock Pages: 6

Brand: Camtree Hunt Pages: 5

Brand: Duramaxx Pages: 55

Brand: Wanin USA Pages: 36

Brand: Dahua Pages: 19

Brand: Minolta Pages: 23

Brand: Alinking Pages: 89

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands