AVer EMC1000 User Manual Download Page 32 | Manualshive

Page: 32 / 33

AVer EMC1000 User Manual Download Page 32

30

NOTE- This equipment has been tested and found to comply with the limits for a Class A digital

device,  pursuant  to  Part  15  of  the  FCC  Rules.  These  limits  are  designed  to  provide  reasonable
protection  against  harmful  interference  in  a  residential  installation.  This  equipment  generates  uses
and  can  radiate  radio  frequency  energy  and,  if  not  installed  and  used  in  accordance  with  the
instructions,  may  cause  harmful  interference  to  radio  communications.  However,  there  is  no
guarantee  that  interference  will  not  occur  in  a  particular  installation.  If  this  equipment  does  cause
harmful interference to radio or television reception, which can be determined by tuning the equipment
off and on, the user is encouraged to try to correct the interference by one or more of the following
measures:

1.  Reorient or relocate the receiving antenna.
2.  Increase the separation between the equipment and receiver.
3.  Connect  the  equipment  into  an  outlet  on  a  circuit  different  from  that  to  which  the  receiver  is

connected.

4. Consult the dealer or an experienced radio/television technician for help.



For warranty period, please refer to the warranty card.

FEDERAL COMMUNICATIONS COMMISSION
STATEMENT (CLASS A)

«
...
30
31
32
33
»

Summary of Contents for EMC1000


































Reviews:

No comments