Avaya VSP 4000GSX Series Installation Job Aid Download Page 6

Installing SFP transceivers

Install SFP transceivers by performing this procedure.

1. Remove the transceiver from the protective packaging.

2. Verify that the transceiver is the correct model for the network configuration.

3. Grasp the transceiver between your thumb and forefinger.

4. Insert the transceiver into the proper module on the switch. Apply a light pressure to the

transceiver until it clicks and locks into position in the module.

5. Remove the dust cover from the transceiver optical bores.

Removing SFP transceivers

Remove SFP transceivers by performing this procedure.

1. Disconnect the network fiber cable from the transceiver.

2. Use the locking mechanism on the transceiver to release it. The locking mechanism varies

from model to model as illustrated below.

3. Slide the transceiver from the module slot.

4. If the transceiver does not slide easily from the module slot, use a gentle side-to-side rocking

motion while firmly pulling the transceiver from the slot.

5. Attach a dust cover over the fiber-optic bores and store the transceiver in a safe place until

you need it.

Important:

Discard transceivers in accordance with the proper laws and regulations.

Power specifications for the Avaya VSP 4450GSX series switches

This section describes the regulatory AC and DC power specifications for the Avaya VSP 4000
4450GSX series switches.

The following table describes the regulatory AC power specifications for the VSP 4450GSX-PWR+
switch and its TAA compliant version. The regulatory AC power specifications are based on the
maximum rated capacity of the power supplies and are not based on typical power consumption,
which is lower.

July 2015

Installation Job Aid for Avaya VSP 4000 4450GSX series     

6

Summary of Contents for VSP 4000GSX Series












Reviews: