manualshive.com logo in svg

Avaya Tenovis Integral-55, Configuration Note, Page: 4 / 25

Share
Download
Avaya Tenovis Integral-55 Configuration Note Download Page 4

AVAYA  E1/QSIG

 

4

 

 

The above information is provided by AVAYA Inc. as a guide.  See disclaimer on page 1 

5.0 CONFIGURING THE PBX TO INTEGRATE 

The following programming is intended for certified PBX technicians/engineers.  
The screens shown in this section are taken from an Avaya PBX administration 
terminal.  Some parameters may not appear on all software releases. 

Ensure all required software features are enabled on the PBX.  Access the System 
Parameters Customer Options form.  Below is an example of the forms required for 
QSIG integration, with the required features in 

boldface

. 

Message Waiting: 

 
 
For MWI the correction of PEM 171458 is necessary. 
This correction is first available in Release E070V08_1_2_3. 
 

ICU Setup: 

 
The QSIG Line is configured like a standard QSIG Line.  

The CRC4 Check procedure was in the test case disabled ! 

 
 

 

 

NOTICE: 

The screens in this 

Config Note are only for 

illustration purposes.  

It is recommended that 

a qualified technician 

review the customer’s 

Tenovis I-55 QSig 

programming for 

Summary of Contents for Tenovis Integral-55


























Reviews:

No comments