Avaya P334T User Manual Download Page 148

Page: 148 / 182

Chapter 6

CLI – Layer 2

132

Avaya P334T User’s Guide

<mod_num>

Example:

P330-N# copy tftp SW_image c:\p330\p330web101 EW_archive

c:\p330\p330web201 192.168.49.10 5

Radius Commands

The following radius commands are accessible from Privileged mode.

image-file

Common name for the files that contain the Software
Image and Embedded Web archive (full path)

filename

Embedded Web Manager image file name (full path)

The ip address of the TFTP server

mod_num

Target switch number

• set radius

authentication secret

Enables secret authentication for the
Avaya P330 unit.

Page 133

• set radius

authentication
server

Sets a primary or secondary RADIUS
server IP address.

Page 133

• clear radius

authentication
server

Removes a primary or secondary
RADIUS authentication server.

Page 133

• set radius

authentication retry-
time

Sets the time to wait before re-sending
an access request.

Page 134

• set radius

authentication retry-
number

Sets the number of times an access
request is sent when there is no
response.

Page 134

• set radius

authentication udp-
port

Sets the RFC 2138 approved UDP port
number.

Page 134

Summary of Contents for P334T























































































































































































Search results

Summary of Contents for P334T

Reviews:

Avaya P334T, User Manual, Page: 148 / 182

Search results

Summary of Contents for P334T

Reviews: