manualshive.com logo in svg

Avaya ERS 8600 series, Configuration Manual

The Avaya ERS 8600 series is a high-performance networking solution designed for large enterprises. Get full control over your network with the Configuration Manual, available for free download from manualshive.com. This manual provides detailed instructions on optimizing your network and maximizing performance.

Share
Download
background image

Chapter 29: Interoperability

The Avaya Ethernet Routing Switch 8800/8600 provides interoperability with servers running Linux and

Windows XP. This chapter provides basic configuration and verification procedures for the various

systems.

Interoperability navigation

•

Enabling IPv6 in Windows XP

 on page 345

•

Pinging the switch from a Windows XP system

 on page 345

•

Enabling IPv6 in Linux

 on page 346

•

Pinging the Linux system from the switch

 on page 347

•

Pinging the Avaya Ethernet Routing Switch 8800/8600 from the Linux system

 on

page 347

•

Assigning IPv6 addresses to the Linux system

 on page 348

•

Viewing IPv6 neighbors from the Linux system

 on page 348

Enabling IPv6 in Windows XP

Enable IPv6 to add IPv6 functionality on the Windows XP system.

Procedure steps

1. Open the command prompt.
2. At the prompt, enter 

ipv6 install

.

Pinging the switch from a Windows XP system

Ping the switch to test connectivity.

Configuration — IPv6 Routing

November 2010     345

Summary of Contents for ERS 8600 series





































































































































































































































































































































































































































Reviews:

No comments

Related manuals for ERS 8600 series

D-Link DSL-500 Quick Start Manual preview
DSL-500
Brand: D-Link Pages: 11
D-Link DHP?P309AV Setup Manual preview
DHP?P309AV
Brand: D-Link Pages: 8
D-Link AirPlus DWL-810 Quick Installation Manual preview
AirPlus DWL-810
Brand: D-Link Pages: 8
D-Link DHP-601AV Quick Installation Manual preview
DHP-601AV
Brand: D-Link Pages: 84
D-Link NetDefend DFL-260E Reference Manual preview
NetDefend DFL-260E
Brand: D-Link Pages: 328
D-Link ShareCenter Pulse DNS-320 Quick Install Manual preview
ShareCenter Pulse DNS-320
Brand: D-Link Pages: 2
D-Link DFL-210 - NetDefend - Security Appliance Firewall Registration Manual preview
DFL-210 - NetDefend - Security Appliance
Brand: D-Link Pages: 19
D-Link DFL-M510 Faq preview
DFL-M510
Brand: D-Link Pages: 22
Dahua N300 Quick Start Manual preview
N300
Brand: Dahua Pages: 12
D-Link NetDefend DFL-1600 Quick Manual preview
NetDefend DFL-1600
Brand: D-Link Pages: 23
Netis DL4305 Quick Installation Manual preview
DL4305
Brand: Netis Pages: 16
Patton electronics 1000RC User Manual preview
1000RC
Brand: Patton electronics Pages: 9
Qlogic QLE7xxx Series Quick Start Manual preview
QLE7xxx Series
Brand: Qlogic Pages: 8
Gira 0535 00 Installation Instructions Manual preview
0535 00
Brand: Gira Pages: 6
WAGO 750-459 Manual preview
750-459
Brand: WAGO Pages: 48
IDT Tsi310TM User Manual preview
Tsi310TM
Brand: IDT Pages: 207
Supermicro AOC-STG-I2 User Manual preview
AOC-STG-I2
Brand: Supermicro Pages: 15
IEI Technology PulM-1G4T-I211 Quick Installation Manual preview
PulM-1G4T-I211
Brand: IEI Technology Pages: 2

Brands by name

Popular brands

Load more brands