AVANT A37190 Operator'S Manual Download Page 39

Page: 39 / 66

39 (66)

7.5

Rotary hoe

The rotary hoe is intended for small scale soil cultivating and mixing of top soil. The hoe is a simple and robust

tool, and it is equipped with two knife type blades.

Rotary hoe - Specifications

Product number

A37491

Width:

531 mm

Total height:

283 mm

Cultivating depth:

max. 160 mm

Weight

15 kg

Note

Can also be used with angle adapter

Before starting to use the rotary hoe:



Remove all obstacles from the operating area, such as large tree branches or rocks, before starting the

operation.



Remember correct working methods and avoid leaving the driver’s seat unnecessarily.



Remove or mark also all hidden obstacles that could cause damages or risks of injuries, and make sure

that there are no electric cables, water or gas pipes at the reach depth of the equipment.



Also make sure that the blades are intact and can rotate freely, and that there is no string or other foreign

material coiled around the shaft of the rotary hoe.

Summary of Contents for A37190



































































Search results

Summary of Contents for A37190

Reviews:

Related manuals for A37190

Brands by name

Popular brands

AVANT A37190, Operator'S Manual

Search results

Summary of Contents for A37190

Reviews:

Related manuals for A37190

Brands by name

Popular brands