AVANT A37190 Operator'S Manual Download Page 22

Page: 22 / 66

22 (66)

6.2.2

Side shift - Angle adapter 90°

The angle adapter A37323 makes it possible to mount the Multi function drive unit so that it is turned 90

degrees to the left. With the angle adapter the carousel broom sweeps on the left side of the loader, for

instance, and the cable/hose reel is crosswise to the loader and winds the cable longitudinally (in parallel to

the loader).
The angle adapter is bolted on to the Multi function drive unit, and this assembly can then be mounted to the

quick coupling plate of the loader. Make sure that both of the bolts are tightened before using the drive unit

with the side shift adapter.
The angle adapter A37323 is intended to be used only with the Multi function drive unit. Never use it with any

other attachment.

Summary of Contents for A37190



































































Search results

Summary of Contents for A37190

Reviews:

Related manuals for A37190

Brands by name

Popular brands

AVANT A37190, Operator'S Manual

Search results

Summary of Contents for A37190

Reviews:

Related manuals for A37190

Brands by name

Popular brands