manualshive.com logo in svg

AVANT 550, Operator'S Manual, Page: 11 / 28

Share
Download
AVANT 550 Operator'S Manual Download Page 11

 

 

11 (28) 

 

 

To apply a new label:

 Clean the surface thoroughly to remove all grease. Allow it to dry completely. Peel off 

the protective film of the label and press firmly to apply. Take care not to touch the glue of the label. 

 

 

Table 3 - Decal locations and warning messages 

 

Decal 

Warning message 

 

1  A46771 

Misuse hazard - Read instructions before 

use. 

2  A46772 

Crushing hazard -  Do not go under a 

raised attachment; stay away from raised 

equipment. 

3  A46803 

Crushing hazard, moving components. 

Keep clear of moving components. 

4  A46749 

Severing hazard, sharp and strong 

blades.  Follow safe stopping procedure 

before going near the attachment. 

5  A449039 

Stop lever 

6  A447207 

Attachment identification plate 

 

. 

.. 

 

Table 4 - Log splitter 550 - Main components 

1  Frame with Avant quick coupling brackets 

 

2  Operating controls 

3  Stop lever 

4  Frame and stand 

5  Hydraulic cylinder for splitting function 

6  Splitting wedge 

7  Height adjustment of the splitting wedge 

8  Working height adjustment 

9  Moving carriage 

10  Unloading chute 

11  Guard 

12  Multiconnector holder 

 

 

Summary of Contents for 550





























Reviews:

No comments