AVANT 525LPG Operator'S Manual Download Page 32

Page: 32 / 36

Service and maintenance instructions

525 LPG

Filters

Following pictures and tables show the location and part numbers for the filters..

1. Air filter

2. Engine oil filter

3. Hydraulic oil filter, return

4. Hydraulic oil filter, pressure

Filter kit A414037 includes:
64956 Air filter

64627 Engine oil filter

74093 Hydraulic oil filter, return

64807 Hydraulic oil filter, pressure

65487 LPG filter

Part numbers, filters

AVANT 525LPG filters

Light bulbs

Part no. for standard front light bulb and work light bulb is 64874.

Contact Avant service in case the steel structure of the loader gets damaged. A faulty reparation

can cause a dangerous situation.

In case the ROPS safety frame or the FOPS canopy of the machine gets damaged, the machine

must be taken to Avant service for checking. It is not allowed to repair the ROPS and FOPS.

Storage of the machine

Before long term storage clean the loader carefully and check and touch-up painted surfaces if necessary in

order to avoid rust damages. Grease the greasing points and put oil on piston rods of the cylinders. Take off

the battery and store it in the right way. It is recommended to perform the yearly service before storage.

Close the gas valve and let the engine run until all gas runs out from the pipes. Take off the gas bottle and store

it in upright position in a cool, dry place; protected from heat and sun. Cover well the end of the gas hose

also.

Metal structures of the loader

Summary of Contents for 525LPG





































Search results

Summary of Contents for 525LPG

Reviews:

Related manuals for 525LPG

Brands by name

Popular brands

AVANT 525LPG, Operator'S Manual

Search results

Summary of Contents for 525LPG

Reviews:

Related manuals for 525LPG

Brands by name

Popular brands