background image

17

300S Series

Coupling the attachments

COUPLING THE ATTACHMENTS

Coupling of the attachments into the attachment coupling plate happens as follows:

Stage 1:

• Lift up the two locking pins on either side of the attachment

coupling plate and turn them backward so that they remain

in the locked up position

• Make sure that the pins remain in the up position, otherwise

you cannot couple the attachment properly!

Stage 2:

• Turn the attachment coupling plate with the tilt movement

so that the upper edge of the plate leans forward.

• Drive the loader into the attachment

Stage 3:

• Lift the boom a little so that the attachment lifts off of the

ground

• Pull the boom control lever to the left so that the lower edge

of the attachment coupling plate turns into the attachment

Stage 4:

• Pull the boom control lever more to the left so that attachment

coupling plate turns more and the bolts on the boom push

the pins down in the holes of the attachment.

•

CAUTION! Make sure that the pins lock properly

down in the holes of the attachment.

Stage 5:

• If the attachment is equipped with hydraulic hoses, make

sure to connect the hoses in the quick couplings on the loader

• Engine must be stopped when connecting the hoses. Before

connecting the hoses move the auxiliary hydraulics control

lever in both directions a couple of times in order to release

eventual back pressure.

• Additional information about the coupling is provided in the

instruction manual of the attachment.

•

NOTICE! When fitting an attachment, make sure that

the hydraulic hoses are not overstretched and are not

in a position where they can be trapped during the

operation of the machine and attachment.

Summary of Contents for 300S Series

























Reviews: