AuviTran StageBox Kit Instruction Manual Download Page 12 | Manualshive

Page: 12 / 20

background image

Connecting the GPIO_WCLK card

Installation Manual

SatgeBox Kit V1.0

AuviTran 2011

12

Insert the 12cm long shrink tube supplied in the Stagebox kit on the flat cable.

Connect the flat cable on the GPIO_WCLK card (blue side to the outside of the GPIO_WCLK card).

Push the shrink tube so that it comes into contact with the connector.

On backplane side, pull the flat cable in the opposite direction to the GPIO_WCLK card.

«
...
10
11
12
13
14
...
»

Summary of Contents for StageBox Kit





















Reviews:

No comments

Related manuals for StageBox Kit

Brand: ZOLL Pages: 5

Brand: Accu-Chek Pages: 3

Brand: iBin Pages: 2

Brand: Danelec Pages: 67

Brand: Hagerman Pages: 4

Brand: hager Pages: 2

TECSHOW QUAD SPIDER 60

Brand: Ampro Pages: 9

Brand: MAHA Pages: 21

Brand: MAGUIRE Pages: 47

Rack-mountable 8 x 8 USB 2.0 Interface with MX Core DSP Technology...

Brand: M-Audio Pages: 25

Brand: Ideal Heating Pages: 16

Brand: GE Pages: 37

Brand: IKEA Pages: 24

Brand: Kelso Pages: 21

Brand: Vibration Research Corporation Pages: 333

Brand: BH FITNESS Pages: 24

Brand: Best Fitness Pages: 26

Water Inlet Suction Hose

Brand: Nilfisk-Advance Pages: 8

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands