Autostart AS-1260 Installation Manual Download Page 9

 

9

             

 

 

     LIGHT FLASH RATE

 

 
 
 
 
 

 

 

 
 

FLASHES 

RATE DESCRIPTION 

 

 

Slow 

System has reset. Should occur when Valet switch is turned ON. 
No Tach pulse detected during crank. Should not occur if no pulse is 
detected with in 2 seconds of cranking ‘the unit will force a reset. 

 

 

Slow 

If Parking lights stayed ON for 5 seconds then flashed 3 times slowly when 
Valet switch was turned ON, the unit detected the Ignition line was ON, 
The Hood switch line was grounded and no transmitter was learned. 

Quick 

Button confirmation or end of run time or time canceled or door locks. 

Quick  

Remote start is locked out. See Tach watch lockout.  

Quick  

Indicates that the unit has detected the brakes and cancelled the cranking or 
running cycle. 

Quick  

New remote learned. 

10 

Quick  

Hood was open unit cancelled cranking or running cycle. 

Quick  

Memory being reset: Occurs when resetting unit ON power-up. 

On  

seconds 

If Parking lights ON for 4 seconds, the Hood was opened and the Hood 
switch line was grounded. 

Erratic  

 

If the unit flashes erratically (1to3 flashes, followed by a pause, then more 
flashes), it might be in Playback mode. This occurs when the Hood switch 
was press 3 times. 

Summary of Contents for AS-1260












Reviews: