Autopage MA-200, Installation Instructions Manual

Page: 6 / 8

Oct/23/2006
MA200 IN REV.A 6
b.
The system will advance to [2] LED flash, One chirp with a long chirp. (The factory default settings is
always [1] LED flash, [1] chirp.)
4 Depress the transmitter button ‘A’ again to change the feature again. Simply keep re-depressing the
transmitter button ‘A’ again until the module advances to your desired setting.
5. Depress the transmitter button ‘B’ corresponding to the feature ‘B’ you wants to program.
Press
Transmitter
Button One Chirp /
LED one pulse
Factory Default
Setting
Two Chirps /
LED two pulses Three Chirps /
LED three pulses
Four Chirps /
LED four pulses
1
All Chirps on Siren Chirps on only Horn Chirps on only All Chirps off
2
Automatic Rearm
on Automatic Rearm off
3
F
Active arming Passive arming Active arming with
Passive starter
disable
4 +
F
Horn Chirp 10ms Horn Chirp 16ms Horn Chirp 20ms
Exit:
Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps will confirm exit.
Active Arming With Passive Starter Disables : The “Ground-when-armed output will go active 60
seconds after the ignition is turned off. The LED will flash at half its normal rate when the ignition is turned
off to indicate that the system will interrupt the starter in 60 seconds.
ALARM FEATURE “
II
” PRORAMMING:
1. Turn the Ignition 'switch ‘ON/OFF’ 3 TIMES and staying in the OFF position.
2. Push the Valet switch 4 times and hold in on the 4
th
push until two chirps and a long chirp is heard then
release the valet switch. You are now in the Alarm feature ‘II’ programming mode.
3. Press and release the transmitter button ‘A’ corresponding to the feature ‘A’ you want to program.
Press
T
ransmitte r
Button
One Chirp /
LED one pulse
Factory Default
Setting Two Chirps /
LED two pulses Three Chirps /
LED three pulses
Four Chirps /
LED four pulses
1
H1/5 Brown Wire =
Constant Siren
output H1/5 Brown Wire =
5-second pulse Siren
output H1/5 Brown Wire =
Random pulse Siren
output
2
H2/6 Gray Wire
Channel 3 Output =
1 second pulse H2/6 Gray Wire
Channel 3 Output =
Latch H2/6 Gray Wire
Channel 3 Output =
Latch with Ignition
4 Chirps = 30-second
5 Chirps = 60-second
6 Chirps = 90-second
3
F
H2/5 Violet Wire
Channel 4 Output =
Momentary output H2/5 Violet Wire
Channel 4 Output =
Latched output H2/5 Violet Wire
Channel 4 Output =
Latch with Ignition
4 Chirps = 30-second
5 Chirps = 60-second
6 Chirps = 90-second
4 + F
Enable the out of
range check Disable the out of
range check.
Exit:
Turn Ignition to 'ON' position, or leave it for 15 seconds. 3 long chirps will confirm exit.
Momentary output = The momentary output selection will output a negative signal from the Channel 4
output immediately when the channel 4 button is pressed and will continue until the button is release.
Latched output = The latched output selection will output a negative signal as soon as the Channel 3 (4)
button is pressed and will continue until the button is pressed again.
Latched /Reset with ignition = A latched / reset with ignition output works similar to the latched output,
but will also reset (output will stop) when the ignition is turned on then off.