Autopage Car-Pro CPX-RS2 Installation Manual Download Page 9

August, 2005 

RS2 

9

 
 
H5.

 Red 

3-PIN CONNECTOR. – Windshield Receiver /Antenna

 

The windshield receiver/antenna mounts on the windshield (Inside). We suggest you mount it on the lower left or upper 
left-hand side of windshield. 
Warning! Do not mount in such a manner that it obstructs the driver’s view. 

For Optimum Performance

 

the receiver/antenna whip must be vertical facing up.

 

- Remove the protective tape backing. 
- Carefully align the receiver/antenna and apply to windshield. 

Route the black connector wire behind the trim and connect to receiver/antenna.   

- Connect the other end to the control module. 
- Special considerations must be made for windshield glass as some newer vehicles utilize a metallic 
  shielded window glass that will inhibit or restrict RF reception. In these vehicles, route the windshield   
  receiver/antenna module away from metallic shielded window glass as far as possible.   

   

H6.  White 3-PIN DOOR LOCK CONNECTOR

 

 

 

 

1. 
Blue

 Wire   

 

2. 
Green

 Wire

 

 

 

-

 

 ) Lock 

 

 

Green 

  

 

 

 

-

 

 ) Unlock  Blue 

 

 

  

 

 
 

 

NEGATIVE TRIGGER DOOR LOCK SYSTEM 

Blue Wire Door Unlock

 

Green Wire Door Lock

 

Locking 
Master 
Switch 

To Exiting 
Door Lock Relay

 

 

+12V

 

Master Door

 

Lock Switch

 

To Door

 

Lock Motors

 

Unlock Wire

 

3 Pin Plug

 

To Alarm

 

3-WIRE POSITIVE DOOR LOCK

 

30

 

86

 

87a

 

85

 

87

 

30

 

86

 

87a

 

85

 

87

 

+12V

 

Green Wire

 

Blue Wire

 

 

 
 

 

+12V

 

Master Door

 

Lock Switch

 

X

 

X

 

Splice

 

Splice

 

Cut the Existing

 

Lock Wire

 

To  Door

 

Lock Motors

 

Cut the Existing

 

Unlock Wire

 

3 Pin Plug

 

To Alarm

 

5-WIRE ALTERNATING DOOR LOCK

 

30

 

86

 

87a

 

85

 

87

 

30

 

86

 

87a

 

85

 

87

 

+12V

 

Green Wire

 

Blue Wire

 

 

 
 

 
 

Summary of Contents for Car-Pro CPX-RS2


















Reviews: