background image

C3 RS915 REV. O1 

12 

be  shown  on  the  LCD  screen.  This  reading  may  be  higher  than  actual  ambient  temperature  due  to  the 
greenhouse effect and is relative only to the inside vehicle temperature.

 

G. TO TURN OFF THE REMOTE START:

   

When the engine is running (by remote start), if you want to stop it,   

1.  Press 

 

button once on the remote transmitter under the remote start mode. 

2.  Move the optional remote start enable toggle switch to OFF position. (If installed) 

3.  Press the brake pedal   

The vehicle will shut down and turn off the parking light to indicate the engine has stopped. 

H. SHUT-DOWN INPUT FOR REMOTE STARTER:   

If any of the following conditions exist while the system is operating, the engine will not start or will 
shut down immediately: 

1. The hood is opened. 
2. The brake pedal is pressed. 
3. The parking (hand) brake is released (For Turbo Timer Mode) 
4. Engine is over-

revved. {“Tachometer checking type” only}

 

5. The pre-programmed run time 

(5 /10 / 20 / 30 minutes)

 has elapsed. 

6. Press 

 

button on the remote transmitter under remote start mode. 

7. The system trigger. 
8. The vehicle refused to start running after {3} unsuccessful attempts. 

I.  DISABLING THE REMOTE START SYSTEM: (If installed) 

This  feature  allows  your  system’s  remote  start  unit  to  be  temporarily  disabled  to  preve

nt  the  vehicle  from 

being  remote  started  accidentally.  This  feature  is  useful  if  the  vehicle  is  being  serviced  or  stored  in  an 
enclosed area. To disable the  remote  start,  move  the  optional  remote  start  enable  toggle  switch  to  the  OFF 
position.

   

МSVMASTER

 - Установка и разблокировка охранных систем автомобилей - 

http://www.msvmaster.lv

МSVMASTER

 - Установка и разблокировка охранных систем автомобилей - 

http://www.msvmaster.lv

Summary of Contents for C3-RS-915 LCD

















Reviews: