Automatic Technology GDO-2 SecuraLift Installation Instructions Manual Download Page 4

4

PRODUCT FEATURES

Thank you for purchasing the ATA
SecuraLift

®

Automatic Garage Door

Opener. This opener is designed to suit
sectional overhead and one piece tilt up
doors. The components and materials
used in this opener are of the latest 
technology and highest quality. Listed
below are some of the many features.

OPERATION

To open or close the door simply press
the hand held transmitter, the wall
mounted transmitter, or optional wall
switch for two seconds. During an open
or close cycle the door can be stopped
by pressing the button while the door is
in motion. The next actuation will move
the door in the opposite direction.

HOPPING CODE

Every time a transmission is made  from
the 

remote

transmitter a new security

code is generated. The number of
possible code combinations is over 4.29
billion. This greatly enhances the
security of the system. Code “grabbing”
is made a thing of the past. 

ALPS (AUTOMATIC LIMITS
POSITIONING SYSTEM)

A revolutionary door travel limits
positioning system., the new ALPS
technology does away with manual
adjustment of the doors’ limits position
using mechanical parts, such as cams
and micro switches.

The ALPS technology automatically
calculates the doors’ travel limits and
stores it in memory. If the door is
moved manually within the travel limits
during a power failure, the ALPS will
recognise this once the power is 
restored and stop at the correct limit
position if the door is activated.

During installation the hand held
transmitter can be programmed to set
the door limits positions.

ISS (INTELLIGENT SAFETY
OBSTRUCTION SYSTEM) 

While the door is performing a close
cycle, should it hit an obstacle or be
restricted in some manner, it will
automatically reverse. The amount of
force the door should encounter before
reversing is automatically adjusted by
the doors control system during the
initial installation of the automatic door
opener. The door will also stop if
restricted whilst opening. The Safety
Obstruction Force should be checked at
least once a month. See installation
manual for instructions.

SECURITY CODE STORE

The SecuraLift

®

Garage Door Opener

uses state of the art technology in
storing your selected transmitter 
security code. Up to 23 different
transmitters can be stored in the openers
memory.

OVER LOAD INDICATOR

When the maximum opening and 
closing capacity of the opener is
exceeded an audible beeper will sound
to indicate that an overload has
occurred.

AUTO COURTESY LIGHT

The courtesy light on the opener comes
on automatically whenever the door is
activated. The light can also be
switched on and off without operating
the door. This is done by pressing the
button on any hand held or wall 
mounted transmitter which has been
stored with the light code.The light will
stay on for approximately three minutes
then switch off. This time is also
adjustable. 

VACATION MODE

A hand held transmitter can be 
programmed to lock and unlock all
other transmitters that have being
programmed into the openers’ memory.
The vacation mode can be used when
the door is left idle for long periods of
time.

PET (PEDESTRIAN) MODE

The hand held transmitter can be
programmed to open the door partially
so that the family pet can enter and exit
the garage at any time. You may also
wish to open the door to a height 
suitable only for pedestrian access. The
door opening position is also 
programmable.

AUTO CLOSE MODE

The opener can be programmed to
automatically close after an open cycle.
The auto close time is adjustable. It is
compulsory to install a Photo Electric
Beam if this mode is selected, otherwise
the door may cause personal injury or
damage to property.

PHOTO ELECTRIC BEAM
(OPTIONAL)

The opener has an input for a photo
electric beam to be connected for extra
safety protection and use of the auto
close mode.

MANUAL OPERATION

The opener is equipped with a unique
manual disengaging device. If the
power to the opener is disrupted for any
reason the door can be put into manual
mode by pulling down on the string
handle on an angle towards the door.
This will allow you to manually open or
close the door. to re-engage the opener
pull the string handle away from the
door.

Summary of Contents for GDO-2 SecuraLift

























Reviews: