Automatic Technology GDO-11 Ero, Installation Manual, Page: 2 / 23

GDO-11 Ero Installation Manual 2
Table of Contents
1. Important Safety Warnings! 3
2. Before you Begin 5
3. Tools Required 5
4. Kit Contents 6
5. Position 6
6. Fit the Opener 7
7. Bracket Position 7
8. Perforated Angle 8
9. Mounting Brackets and Arms 9
10. Connect to Power 9
11. Setting Limits 10
11.1 Setting the Datum: 10
11.2 Set the Limit Positions: 10
11.3 Clearting the Door Limit Positions: 11
11.4 Re-profiling the Door: 11
11.5 Controller memory reset: 11
11.6 Setting the PET (Pedestrian Mode) position: 11
12. Safety Testing 12
12.1 Test the Close Cycle 12
12.2 Testing the Open Cycle 12
12.3 Test the Manual Door Operation 12
12.4 Adjusting Safety Obstruction Force 12
12.5 To Increase Force Pressure 12
12.6 To Decrease Force Pressure 12
12.7 To Recall Factory Set Force 12
12.8 To Recalculate Force Margins 12
13. Control Board & Accessories 13
13.1 Control Board Layout 13
13.2 Auxiliary Output 13
14. Coding a Transmitter 14
14.1 Storing the Transmitter Code 14
14.2 Remotely Coding Transmitters 14
14.3 Vacation Mode 14
14.4 Aux Output 14
14.5 PET (Pedestrian) Mode 15
14.7 Erasing All Transmitter Codes 15
14.6 Courtesy Light 15
14.8 Optional Wall Mounted Transmitter 15
15. Opener Safety & Security 16
15.1 Your Door CAN NOT be used when: 16
15.2 Your Door CAN be used when: 16
15.3 To Disengage the Opener: 16
15.4 To Re-Engage the Opener: 16
16. Operating your Opener 16
17. User Operating Controls 17
18. Door Status Indicators 17
19. Specifications 18
20. Troubleshooting 19
21. After Installation Care 22
21.1 Service Checklist 21
21.2 Battery Replacement 22
21.3 Battery Disposal 22
21.4 Warranty 22
Installation Instructions
Home Owner Instructions
WARNING! IMPORTANT SAFETY INSTRUCTIONS
FOLLOW ALL INSTRUCTIONS SINCE INCORRECT INSTALLATION CAN LEAD TO SEVERE INJURY.
• before installing the drive, remove all unnecessary ropes or chains and disable any equipment, such as locks, not needed for
powered operation;
• before installing the drive, check that the door is in good mechanical condition, correctly balanced and opens and closes
properly;
• install the actuating member for the manual release at a height less than 1,8 m;
• install any fixed control at a height of at least 1,5 m and within sight of the door but away from moving parts;
• permanently fix the labels warning against entrapment in a prominent place or near any fixed controls;
• permanently fix the label concerning the manual release adjacent to its actuating member;
• after installation, ensure that the mechanism is properly adjusted and that the drive reverses when the door contacts a 40
mm high object placed on the floor.
• necessary information for the safe handling of a drive weighing more than 20 kg. This information shall describe how to use
the handling means, such as hooks and ropes;
• the drive must not be used with a door incorporating a wicket door (unless the drive cannot be operated with the wicket door
open);
• after installation, ensure that parts of the door do not extend over public footpaths or roads.
• vertical doors and gates need an anti-drop feature or device;
• information if a hazardous part of the drive is intended to be installed at a height of at least 2.5 m above floor level or other
access level;
• except for horizontally moving pedestrian doors, ensure that entrapment due to the opening movement of the driven part
is avoided