background image

3

unpacking

The Snackshop LCM is assembled and packed so that a min-
imum amount of time is necessary for preparation to install it
on location. The following steps are recommended to insure
correct unpacking.

1. Shipping Damage: Thoroughly inspect the exterior of the

carton for damage which may have occurred during ship-
ment. Report any damage to delivering carrier and follow
their instructions.

2. Remove staples from lower edge and those at top of carton,

and slit carton vertically at the taped corner. Open and
remove carton. Remove the remainder of the packing mate-
rial. Machines shipped with a lock in place, the keys are
located in the coin return cup.

3.

Remove Vendor With A Fork Lift Truck:

Remove the car-

ton from the vendor. Open the door on the vendor and
remove the hold down bracket at the front center of the cab-
inet base and lose the vendor door. From the front of the
vendor tip the vendor backward and run forks under the cabinet.

4.

Removing Vendor Without A Fork Lift Truck:

Remove the

carton from the vendor. Remove 1/4" piece of plywood locat-
ed just behind the front legs, then open the door on the ven-
dor and remove the hold down bracket at the front center of
the cabinet base and close vendor door. From the front of
the vendor tip the vendor back far enough to clear the wood

strip across the front of the base. Slide vendor toward the
back until the back legs are off the base and pull base out.

5. On machines with lock in place, unlock, and turn handle to

open door. When no lock is furnished, remove tape and turn
handle. Swing door it its full open position.

6. Remove all packing tape and paper from various areas of

machine and the shipping strap.

7. Warranty:The warranty card is attached to the cover of this

manual. It must be filled out in full and mailed at once to
insure coverage.

NOTE: Machines with refrigeration units delivered on
their sides should be stood upright for 24 hours
before the machine is plugged into an outlet.

NOTE: Because the weight concentration is toward
the back of the cabinet trucking and lifting should be
done from the back. CAUTION should be taken when
trucking from side.

IMPORTANT: A set of anchoring brackets are sent
with each machine. The kit is located in the bottom of
the machine complete with instructions. It is recom-
mended that this kit be installed to prevent shifting of
the machine. Part # 660438















◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆  

WATCH THROUGHOUT THE MANUAL FOR THIS   

SPECIAL 

DIAMOND MARK.THIS INDICATES A       

POINT OF SPECIAL INFORMATION OR A HINT    
T H AT WILL ASSIST YOU IN SETTING UP, OPERAT I N G
OR TROUBLESHOOTING THE MACHINE.

◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆◆  

CAUTION: Certain procedures in both the operating section and the service section require that voltage
be on the machine. Only trained personnel should perform this function. Exercise extreme caution while
performing these procedures. These procedures will be marked with the lightening bolt symbols as it
appears at left.

CAUTION: Certain procedures in both the operating section and the service section requires a qualified
trained technician to perform the particular task at hand.These procedures will be marked with the
exclamation symbol as it appears at left.

Serial Number Definition

Automatic Products int’l ltd. has introduced a new serial numbering method to permit better tracking of machines, and any
changes that occur. This information is being provided to you so that you understand the information contained in the serial
number, and so that when you are making an inquiry about a specific machine, or require a warranty replacement, that you
provide us with the complete serial number. The location of the serial number plate in the machines has not changed.The
serial number plates are located inside the machine in the upper right hand corner of the cabinet, and adjacent to the power
cord on the back of the cabinet.
It is essential that the complete serial number be reported when reporting any problems or claiming any wa r ranty replacements.
The new serial number format is explained in the example below:

Sequential build Number
starts at 001 each day

Numerical Day of the Year - Jan 1st = 001, Dec 31 = 365

Year 99 - Last two digits of year

First Digits indicate model, example shown is a 123A Glassfront Merchandiser - The machine identification may
contain up to six characters dependent upon the model.

Suffixes
A

- indicates all design changes incorporated upon the introduction of the new chiller unit

C

- indicates a chilled machine

E

- indicates a machine built specifically for export outside North America

1

2

3

A

9

9

3

6

5

0

0

1

3

Summary of Contents for SNACKSHOP LCM1 Series





















































Reviews: