Automatic Products SNACKSHOP LCM1 Series, Instruction Manual, Page: 12 / 52

8
program operation
NOTE:The machine should be on “CAnn”.
4. PRESS #4 - Price Set Mode. To begin the price setting
procedure, press key [4]. The controller will display "Prc"
and wait for a selection to be entered.Once the selection is
entered, the current price will be displayed. The price can
now be increased with the scrolling up (
▲
) button or
decreased with the scrolling down (
▼
) button.
(Figure 10.)
The maximum price can be set to $99.95. Setting a
selection price to “0.00” will put it on free vend.
Step Procedure.
a. In the Service mode, press [4] (displays "Prc").
b. Press selection item to be priced (displays current price
"xx.xx").
c. Using the up (
▲
) or down (
▼
) buttons will change to the
price desired. (Figure 10.)
d. Repeat steps "b" and "c" to price another selection.
e. To exit this mode, press another function key or leave
the Service mode by pressing the mode switch.
5. PRESS #5 - Test Vend Mode. To test vend a single
selection, press key [5]. The controller will display "SLct"
and wait for a selection to be entered.Once the selection is
entered, a vend of the motor will be attempted. If the vend
is successful, the controller will blank the display and exit
the test vend mode. If the selected motor fails, the controller
will display "FAiL" for 2 seconds and then exit.
Step Procedure.
a. In the Service mode, press [5] (displays "SLcT").
b. Press the motor selection to test vend (machine will
display selection and cycle motor unless vend test fails,
which would display "FAiL").
c. To test vend other selections, press [5] and repeat steps
"a" and "b".
d. To exit this mode, press another function key or leave
Service mode by pressing the mode switch.
PRESS #6 - Diagnostic Vend Test. This feature can be
used to test vend all configured motors within the machine
before installing on location.The controller will display each
selection as a vend attempt is made. If the vend is
successful, the controller will continue on with the next
selection. If the selected motor fails the controller will
display "FAiL" for 2 seconds and then continue. When a
vend attempt on all motors has been completed, the
controller will blank the display and exit the test vend mode.
To exit this mode, press another function key and hold until
the current vend is completed or exit the Service mode.
(See page #43 for diagnostic error table).
6. Vend Option Mode. To enter the vend option mode, press
key [E]. The controller will display “OPtn” and wait for
additional key to be pressed for following features:
a. Press key [A] -
Force Vend.
(displays “FrcY” or “Frcn”)
Press key [A] again to toggle between force vend
enabled (“FcrY”) and force vend disabled (“Frcn”).
b. Press Key [B] -
Escrow Enable.
(displays “EScY” or “EScn”)
Press key [B] again to toggle between escrow enable
(“EScY”) or escrow disable (“EScn”).
The escrow enable option allows the validator to return
a bill inserted by a customer who changes their mind.
The bill inserted will be held by the validator without
being stacked. When the coin return button is pushed,
the bill is returned.
c. Press key [C] -
Multi-Vend.
(displays “MuLY” or “MuLn”)
Press key [C] again to toggle between multi-vend enable
(“MuLY”) or multi-vend disable (“MuLn”).
The multi-vend option allows the customer the option to
vend multiple items without reentering credit. Change
will not be returned immediately after a vend and credit
will remain on the display for up to 20 seconds. Escrow
attempts will be valid at any time or change will be
returned after 20 seconds of no vend activity.
d. Press key [D] - Can Drink.
(displays “CAnY”)
Press [D] again to toggle between “CAnY” and” CAnn”.
e. Press key [F] - Free Vend.
(displays “FREY” or “FREN”)
Press key [F] again to toggle between Free Vend
Enable (“FREY”) or Free Vend Disable (“FREN”).
The Free Vend option allows the customer to test vend
each selection motor for proper operation.
N OT E : Test vending a selection that had failed
p r ev i o u s ly, will reset if the motor successfully
completes a vend cycle.
CAUTION: THE FOLLOWING
PROCEDURE REQUIRES THAT THE
MACHINE HAVE POWER APPLIED AND
A POTENTIAL ELECTRICAL SHOCK
HAZARD EXISTS.
CAUTION: THE FOLLOWING
PROCEDURE REQUIRES THAT THE
MACHINE HAVE POWER APPLIED AND
A POTENTIAL ELECTRICAL SHOCK
HAZARD EXISTS.
CAUTION: THE FOLLOWING
PROCEDURE REQUIRES THAT THE
MACHINE HAVE POWER APPLIED AND
A POTENTIAL ELECTRICAL SHOCK
HAZARD EXISTS.