manualshive.com logo in svg

Automatic Heating AHGR410AW Series, Installation And Instruction Manual, Page: 6 / 26

Share
Download
Automatic Heating AHGR410AW Series Installation And Instruction Manual Download Page 6

Inverter Air Source Heat Pump (AHGR410AW) - Installation and Instruction Manual

02. Safety Precautions

2.3 Attention

Installation

Operation

Keep away from flammable substances.

DO NOT install the unit near flammable 
gases or substances. Leakage of these may 
cause fire.

Check the baseplate / 
foundation regularly.

Inspect the baseplate or foundation of the 
equipment at least once every month to 
avoid any decline or damage.

Switch off the power during 
maintenance.

Please switch off the power when cleaning 
the equipment or during maintenance

Provide appropriate machine foundation.

Make sure that the unit is securely positioned 
and that its base is strong enough to prevent 
it from falling.

Provide a circuit breaker.

Provide an appropriate and properly-sized 
circuit breaker for the unit. Lack of circuit 
breaker could lead to electrical shock or fire.

Do not use copper or iron as fuse.

It is prohibited to use copper or iron as fuse. 
The appropriate fuse for the equipment must 
be selected and installed by an electrician.

Do not spray flammable gas to the unit.

DO NOT spray flammable gas to the heat 
pump to avoid fire.

6

Summary of Contents for AHGR410AW Series



























Reviews:

No comments