Automatic Heating AHGR410AW Series Installation And Instruction Manual Download Page 11 | Manualshive

Page: 11 / 26

Automatic Heating AHGR410AW Series Installation And Instruction Manual Download Page 11

Inverter Air Source Heat Pump (AHGR410AW) - Installation and Instruction Manual

04. Installation

4.1 Schematic Diagram for Air-conditioning

4.2 Equipment Selection & Sizing

4. Installation

Considering local climate conditions, space
restrictions, and insulation level, calculate the
required cooling (heating) capacity per square
meter. Compute the total capacity needed for the
whole area.
Then choose the

suitable heat

pump

's

model,

considering their temperature requirements
and outputs specified below:

Cooling Only Unit

Chilled water outlet temperature: 5-15ºC
Maximum ambient temperature: 43ºC

Heating and Cooling unit

Cooling chilled water outlet temperature: 5-15ºC
Maximum ambient temperature: 43ºC

Heating unit

Warm water inlet temperature: 40-50ºC
Minimum ambient temperature: -10ºC
Inverter air source heat pumps are generally used
in houses, offices, hotels, and other establishments
that need heating or cooling in different areas and
that need to be controlled separately.

Connecting Hose

Water Pump

Non-Return Valve

Temperature Meter

Three-Way Valve

Expansion Tank

Pressure Differential Bypass Valve

Automatic Refill Valve

General Valve

Y-Type Filter

Pressure Meter

Vent Valve

Safety Valve

Heat Pump

Inlet

Buffer Tank

Second Floor

First Floor

City

Water

To City Water

Outlet

11

«
...
9
10
11
12
13
...
»

Summary of Contents for AHGR410AW Series



























Reviews:

No comments