manualshive.com logo in svg

Automatic Heating AHGR410AW Series, Installation And Instruction Manual, Page: 14 / 26

Share
Download
Automatic Heating AHGR410AW Series Installation And Instruction Manual Download Page 14

Inverter Air Source Heat Pump (AHGR410AW) - Installation and Instruction Manual

05. Control & Operation

5.1. Main Interface Display and Function

5. Control & Operation

1

2

3

4

5

6

7

10

9

8

Name

Function

1

On/Off

Switch ON and OFF. 
Red indicates ON, while grey indicates OFF.

2

Mode

Hot water mode, heating mode, cooling mode, hot 
water+heating mode, or hot water+cooling mode can 
be selected

3

Temp. Setting

Sets the target temperature

4

Fast heating

Starts rapid heating. 
This key will be displayed during heating.

5

Timer Setting

Set the timer. White indicates “disabled”, while green 
indicates “enabled”.

6

Setup

Check the status of the unit, time, factory parameter, 
temperature curve, timer setting, and mute setting.

7

Fault

This icon will flash whenever there is an error. 
The display will enter Failure Record Interface upon 
tapping this icon.

8

Defrost

Machine is in defrosting mode when this icon is shown

9

Hot Water Mode Machine is in hot water mode when this icon is shown

10 Cooling Mode

Machine is in cooling mode when this icon is shown

Key Functions

1. Power On Interface

2. Starting Up Interface

Note: The controller can display the temperature in ºF or ºC 
depending on the unit model.

14

Summary of Contents for AHGR410AW Series



























Reviews:

No comments