AutoCommand 20036 Installation Manual Download Page 4

20036 - 20038                                                                       Page 7

Page 6                                                                    20036 - 20038

Ignition Key Diagram for Steps 4-7

                            

         Lock/Off   ACC

RUN

       

ACC

START

4

Thick Blue Wire

Ignition 1

Attach the 

Thick BLUE 

14 gauge wire (Ignition 1) to the ignition 1 wire

coming off the key switch behind the steering column.  This is a wire which
shows positive (+12v) on the test meter in the run 

and 

start position, but is off

in the lock/off and accessory position.

5

Thick Green Wire

Ignition 2

Most cars (especially newer cars) have a second ignition wire that is neces-
sary.  Use the 

Thick GREEN 

14 gauge (Ignition 2) wire for this connection.

This is a wire that shows positive (+12V) on the test meter in the run position.
It may be best to leave this wire until the end to determine whether the vehicle
needs this wire to operate some of the accessories.    Note -- setting dip-switch
option 10 (described in Step 29) will cause this wire to be off during crank.

6

Thick White Wire

Accessory

Attach the 

Thick WHITE 

14 gauge wire to the accessory wire coming off of

the key switch behind the steering column area.  This is a wire which shows
positive (+12v) on the test meter in the run and accessory position, but is off
in the start and off position.

All dipswitches should be OFF  (up position) during the installa-
tion.

POWER & IGNITION WIRES

The AutoCommand® module (large black box) will be installed under the dash,
once all wiring has been completed.  

Do not mount the module at this time

because you will need to check the diagnostic lights as the installation
progresses.  

Locate (or drill a hole) in the firewall to run all of the long wires (12

AWG PINK, 18 AWG YELLOW, VIOLET, GREEN, and BLUE) through the firewall
to the engine compartment.  The remaining short wires stay in the passenger
area.  Leave about a foot of length at the harness end under the dash for ease of
working and visual access to the diagnostic lights.

(Note:

Always connect up the 

Black

 and 

Pink

 wires before connecting up

any of the other wires.)

2

Black Wire

Ground

Optimum ground connection is critical for proper operation of this unit, as well
as transmitter range.  Connect this 

BLACK 

wire to a very good clean chassis

ground in the driver’s side kick panel area.  Use the small red ring terminal if
needed.  The metal bracing around or beneath the dash board is not adequate.

3

Long Pink & Short Pink Wire

Power (+12V)

The 

LONG PINK 

wire goes through the fire wall and connects to the 

SHORTER

PINK 

wire with fuse holder.  

We recommend getting power directly at the

b12V terminal. 

 Connect the ring terminal on the SHORT PINK

 

wire to

the +12 volt terminal of the battery.  Strip back some insulation and then solder
the two ends of the PINK wires together, or use the Yellow Butt connector to
connect these.  Either way, you must have a very good connection.  Install the
30 Amp green fuse.

As soon as the Pink (Power) wire is connected the GREEN LED will come on and
go out. (If the unit is already initialized, the GREEN LED will come on for several
seconds while the RED LED flashes 4 times.)

NOTE: WE STRONGLY RECOMMEND GETTING POWER AT THE

BATTERY.  ALSO, FAILURE TO INSTALL THE FUSE HOLDER AND

30 AMP FUSE TO THE PINK WIRE VOIDS ALL PRODUCT WAR-

RANTIES, BOTH WRITTEN AND IMPLIED!

Summary of Contents for 20036
















Reviews: