background image

                                                                                  

 

20

1. Press 

  first, within 3 seconds press and hold 

 

and 

 

buttons at the same time for 2 seconds.  Two beeping 

sound and the “

” icon will be  displayed on the LCD 

screen to indicate the second transceiver pin code is 
programmed. 

2. While the “

” icon is displayed on the LCD screen , you 

can remote control and communicate with a second vehicle 
security system . It has two short “bi” sounds  while pressing 
the button of the LCD screen transceiver.

 

 

Back to 1st Car Operation: 

1. Press 

  first, within 3 seconds press and hold 

  and 

  buttons at the same time for 2 seconds.  One long 

beeping sound  and the  “

”  timer icon will  be 

displayed on the LCD screen indicating the system is back 
to the first transceiver pin code. 

2.  While the “

”  timer icon  is displayed  on the LCD 

screen, you can remote control  and communicate with the 
first vehicle security system.  It has  one  short “bi” sound 
while pressing the button of the LCD screen transceiver.

 

 

 
 
 
 
 
 
 
 
 
 

REMOTE START OPERATION:  

 

A. TO REMOTE START THE VEHICLE:

 

When you want to start your vehicle,  

1. Press 

 

button once on the transmitter. 

2. The parking light will activate to indicate the remote start 
received the signal. 
3. The engine will start in approximately 5 seconds. 
4. Once the engine is running, after couple seconds the parking 
lights will turn on and the climate controls will activate and adjust 
the vehicle’s interior temperature to your preset setting. (While the 
vehicle is running, the “minutes” digit on the LCD screen will flash 
and the will indicate count down timer based on the 5, 10, 20 or 30 
minute run time set up by your installation center.) 
5.  The vehicle will run for a programmable 5 to 30 minute cycle 
before shutting down. (When the unit shuts off the count down timer 
will turn off and the transmitter will play a melody.) 

NOT  E: The Remote Start Unit will not start the vehicle if any one of the 

following conditions exists: 
1. The hood is opened. 
2. The brake pedal is pressed.

 

3. T he optional remote start enable toggle is switched to the “OFF” 
position. (If installed) 

Activate Remote 
Start   

 

 

Engine Running 

 

Summary of Contents for C3-RS-727A LCD



























Reviews: