background image

14

11

BATTERY TEST (cont.)

If the reading is below 7.2 Volts you will get the following:

Surface charge removed if 

detected.

Wait for test results.

Bar at the bottom of the screen will 

show the tests progress.

The BVA-230OZR serial number and test number are displayed to help 

reference the test to the print out.

Wait for instructions before cranking engine.  

If the current draw is between 75A & 250A (for gas powered engines) the starting 

system is likely good and the following screen will appear

If the current is under 75A a solenoid connection or corrosion problem is likely and the 

following screens appear.

STARTER TEST cont

>START ENGINE

'N' TO CANCEL

#40 12V START.

CURRENT 200A

- PASSED -

'Y' TO CONTINUE

The BVA-230OZR will test the 

starting system. A bar at the 

bottom of the screen will show the 

tests progress.

TESTING STARTER

PLEASE WAIT ...

Press the (-Down) key to dis-

play the next screen. Press Y or 

N to go to the main menu.

#73 12V START.

CURRENT 60A

- FAILED -

'Y' TO CONTINUE

TESTING BATTERY 

PLEASE WAIT...

S#22010 T#32

IS THIS A 6V

BATTERY?

'N' OR 'Y'

REMOVING SURFACE

CHARGE...

S#22010 T#32

Press the (+Up) or (-Down) key 

to increment or decrement to the 

rated CCA of the battery. Press 

'Y' to enter and start the test. 

If you are testing a 6V battery 

press 'Y'. If you are testing a 12V 

battery press 'N'

If OTHER brand was selected, the 

battery rating type is needed. Use the 

(+Up) or (-Down) key to move the cursor. 

Press 'Y' to select. Depending on the 

battery type the choices will vary. The 

options are CCA, CA, MCA, and AH.

For some battery 

categories the battery 

type is needed. Use the 

(+Up) or (-Down) key to 

move the cursor. Press 

'Y' to select. Press 'N' to 

go back  to the Battery 

Category screen.

For marine batteries the battery function 

type is needed. Use the (+Up) or (-Down) 

key to move the cursor. Press 'Y' to 

select. Press 'N' to go back to the Battery 

Type screen.

ENTER BATTERY 

RATING: 600 CCA    

USE +/- 

'Y' TO CONTINUE

 BATTERY RATING

>MCA

 CCA

 CA

 BATTERY TYPE?

>STANDARD

 AGM

 'Y' TO SELECT

 BATTERY TYPE?

>STD. STARTING

 STD. DEEP CYCLE

 AGM STARTING

Summary of Contents for BVA-230OZR













Reviews: