background image

45

Class II: Sensitive area or organization & military area & border between countries

: Warning area

APP will give a warning information when the aircraft enters the area of 2 km from the airport.

: Restricted area

A circular area centered on this area and with a radius of 1km.

Remark

When the aircraft enters any takeoff restricted area, it will land automatically. When the
aircraft enters the altitude restricted area, its maximum allowable altitude will be lowered
accordingly. Please pay special attention to the warning message displayed by Autel Voyager
App.

6.1.2 Indexes of laws and regulations for Chinese UAVs

Users of UAVs must check local regulations before flying, and perform flight tasks under legal
and safe conditions. The following is a list of regulatory documents in China for your reference.
Users in overseas regions shall find local regulations by oneself.

1. Legal Laws and regulations

Civil Aviation Law of the People's Republic of China (Order of the President of the People's
Republic of China [1995] No. 56), promulgated on October 30, 1995, implemented on March
1, 1996, and last revised on December 29, 2018.

2. Administrative laws and regulations

Military Airport Clearance Regulations (G. F (2001) No. 29), promulgated on August 12,
2001, and implemented on August 12, 2001.

The Basic Flight Rules of the People's Republic of China (Order No. 312 of the State
Council), promulgated on July 27, 2001, implemented on August 1, 2001, and last revised on
October 18, 2007.

General Aviation Flight Control Regulations'' (Order No. 371 of the State Council and the
Central Military Commission).

The Regulations on the Administration of Civil Airports (Order No. 553 of the State Council),
promulgated on April 13, 2009, implemented on July 1, 2009, and last revised on March 2,

Summary of Contents for Dragonfish Pro




















































Reviews: